South bend 8K SB1001 Скачать руководство пользователя страница 72

Страница: 72 / 76

-70-

For Machines Mfg. Since 8/11

Model SB1001 8K

™

Lathe

P A R T S

Labels

The safety labels provided with your machine are used to make the operator aware of the

machine hazards and ways to prevent injury. The owner of this machine MUST maintain the

original location and readability of these safety labels. If any label is removed or becomes

unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at

(360) 734-1540 or www.southbendlathe.com to order new labels.

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

801

PSB1001801

MACHINE ID LABEL

810

PSBLABEL13VS DOOR CLOSED LABEL

802

PSB1001802

EMERGENCY STOP LABEL

811

PSB1001811

SB NAMEPLATE CURVED BRASS

803

PSB1001803

SPINDLE SPEED DIAL LABEL

812

PSB1001812

TRAINED PERSONNEL NOTICE LABEL

804

PSB1001804

SPINDLE SWITCH LABEL

813

PSBLABEL01VS READ MANUAL LABEL

805

PSB1001805

THREE V-WAY DESCRIPTION LABEL

814

PSBLABEL03VS FACESHIELD/GLASSES LABEL

806

PSB1001806

THREAD DIAL CHART LABEL

815

PSB1001815

CHUCK KEY HAZARD LABEL

807

PSB1001807

FEED-THREAD CHART LABEL

816

PSBLABLE08VS ENTANGLEMENT LABEL

808

PSBPAINT-01

SB GRAY TOUCH-UP PAINT

817

PSB1001817

120V ELECTRICITY LABEL

809

PSBLABEL02VS DISCONNECT POWER LABEL

801

802

803

804

805

806

807

808

809

810

811

812

813 814

815 816

817

Содержание 8K SB1001













































































Результаты поиска

Содержание 8K SB1001

Отзывы:

Похожие инструкции для 8K SB1001

Бренды по названию

Популярные бренды

South bend 8K SB1001, Руководство пользователя

Результаты поиска

Содержание 8K SB1001

Отзывы:

Похожие инструкции для 8K SB1001

Бренды по названию

Популярные бренды