South bend 8K SB1001 Скачать руководство пользователя страница 61

Страница: 61 / 76

For Machines Mfg. Since 8/11

Model SB1001 8K

™

Lathe

-59-

E L E C T R I C A L

Electrical Safety Instructions

These pages are accurate at the time of printing. In the constant effort to improve, however, we may

make changes to the electrical systems of future machines. Study this section carefully. If you see

differences between your machine and what is shown in this section, call Technical Support at (360)

734-1540 for assistance BEFORE making any changes to the wiring on your machine.

Shock Hazard:

It is extremely dangerous to

perform electrical or wiring tasks while the

machine is connected to the power source.

Touching electrified parts will result in

personal injury including but not limited to

severe burns, electrocution, or death. For

your own safety, disconnect machine from

the power source before servicing electrical

components or performing any wiring tasks!

Wire Connections:

All connections must be

tight to prevent wires from loosening during

machine operation. Double-check all wires

disconnected or connected during any wiring

task to ensure tight connections.

Modifications:

Using aftermarket parts or

modifying the wiring beyond what is shown

in the diagram may lead to unpredictable

results, including serious injury or fire.

Motor Wiring:

The motor wiring shown in these

diagrams is current at the time of printing,

but it may not match your machine. Always

use the wiring diagram inside the motor

junction box.

Circuit Requirements:

Connecting the machine

to an improperly sized circuit will greatly

increase the risk of fire. To minimize

this risk, only connect the machine to a

power circuit that meets the minimum

requirements given in this manual.

Capacitors/Inverters:

Some capacitors and

power inverters store an electrical charge for

up to 10 minutes after being disconnected

from the power source. To reduce the risk of

being shocked, wait at least this long before

working on capacitors.

Wire/Component Damage:

Damaged wires

or components increase the risk of serious

personal injury, fire, or machine damage. If

you notice that any wires or components are

damaged while performing a wiring task,

replace those wires or components before

completing the task.

Experiencing Difficulties:

If you are

experiencing difficulties understanding the

information included in this section, contact

our Technical Support at (360) 734-1540.

The photos and diagrams included in this section are best viewed in color. You can

see them in color at www.southbendlathe.com.

BLACK

WHITE

GREEN

BLUE

BROWN

GRAY

ORANGE

YELLOW

GREEN

PURPLE

PINK

ORANGE

WHITE

BLUE

WHITE

YELLOW

WHITE

TUR-

QUIOSE

NOTICE:

WIRING DIAGRAM COLOR KEY

Содержание 8K SB1001













































































Результаты поиска

Содержание 8K SB1001

Отзывы:

Похожие инструкции для 8K SB1001

Бренды по названию

Популярные бренды

South bend 8K SB1001, Руководство пользователя

Результаты поиска

Содержание 8K SB1001

Отзывы:

Похожие инструкции для 8K SB1001

Бренды по названию

Популярные бренды