background image

For Machines Mfg. Since 8/11

Model SB1001 8K

 Lathe

-49-

M A I N T E N A N C E

Lubrication

The lathe has numerous metal-to-metal sliding 

surfaces that require regular lubrication to 

maintain smooth movement and ensure long-

lasting operation.

Other than the lubrication points covered in 

this section, all other bearings are internally 

lubricated and sealed at the factory. Simply leave 

them alone unless they need to be replaced.

Before performing any lubrication task, 

DISCONNECT LATHE FROM POWER!

Important: Before adding lubricant, clean away 

any debris or grime from the entry points with 

mineral spirits to prevent contamination of the 

new lubricant.

Oil Gun

Proper lubrication of the spindle bearing and 

chuck fittings is done with a pump-type oil gun 

that has a plastic or rubberized cone tip. We do 

not recommend using metal needle or lance tips 

as they can push the ball too far into the fitting, 

break the spring seat, and lodge the ball into the 

oil galley. Push the rubber or plastic tip of the oil 

can nozzle against the ball to create a hydraulic 

seal, then add the lubricant.

Use the schedule and information in the chart 

below as a daily guide for lubrication tasks.

The following schedule is based on light-to-

medium usage. Some components may need 

to be lubricated more frequently depending on 

usage.

Spindle Bearings

Oil Type .. Mobil DTE Light or ISO 32 Equivalent

Lubricating Device ................ Pump-Type Oil Gun

Amount ................................................. 1–2 Pumps

Frequency .......................................................Daily

The spindle bearing lubrication fittings are 

located on either side of the headstock (see 

Figure 80).

Lubrication Task

Frequency

Page

Spindle Bearings

Daily

This

Page

Feed Direction Gears

Daily

50

Grease Fittings

Daily

51

Longitudinal Leadscrew

Daily

51

3-Jaw Chuck

Daily

52

Bedway & Slides

Daily

52

Figure 80. Spindle bearing lubrication fittings.

Left Spindle

Bearing Fitting

Right Spindle

Bearing Fitting

Use only an ISO 32 equivalent oil to lubricate 

the spindle bearings. Using a heavier lubricant 

such as grease will cause the bearing to run 

hot and cause excessive machine wear.

Содержание 8K SB1001













































































Отзывы: