Sorel HCC 4 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

Sorel HCC 4 Скачать руководство пользователя страница 29

29

Special functions

This menu can only be selected and used if additional options or expansion modules

have been built into the controller. The associated supplementary installation, mounting

and operation instructions are then included with the specific expansion.

8.4 Expansions

8.5.1 Turn time

The mixer is switched on i.e. is opening or closing for the timespan set here, then the

temperature is measured to control the flow temperature.

Settings range: 0.5 sec to 3 sec. / Default: 2 sec.

8.5.2 Pause-Factor

The calculated pause time of the mixer is multiplied with the value set here. If the pause

factor is “1”, the normal pause time is used, “0.5” will use half the normal pause time, “4”

would quadruple the pause time.

Settings range: 0.1 to 4.0 / Default: 1.0

8.5.3 Increase

If the temperature rises very fast, this value is added to the measured flow temperature

so that the mixer’s reaction is stronger.

If the measured temperature does not rise any more, the measured value is used again.

The measurement occurs once every minute.

Settings range: 0 to 20 / Default: 8

8.5 Mixer

Caution

Settings are only necessary at the time of initial commissioning by the

specialist. Incorrect measurement values can lead to severe unpredict-

able errors.

«
...
27
28
29
30
31
...
»

Содержание HCC 4





































Отзывы:

Нет отзывов