Sorel HCC 4 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Sorel HCC 4 Скачать руководство пользователя страница 20

20

The menu is closed by pressing “esc” or

selecting “Exit settings”.

Settings Heating circuit

5.

Settings Heating circuit

The necessary basic settings required for

the control function of the heating circuit

are made in menu “5. Settings HC”.

This does not under any circum-

stances replace the safety facilities

to be provided by the customer!

Caution

Summer/Winter changeover in daytime mode

If this value is exceeded at outdoor sensor S1 during the daytime mode times, the con-

troller automatically switches the heating circuit off = Summer mode.

If the outdoor temperature drops below this value, the heating circuit is switched on

again = Winter mode.

Setting range: from 0°C to 30°C / default setting: 18°C

Summer/Winterchangeover in nighttime mode

If this value is exceeded at outdoor sensor S1 during the nighttime mode times, the con-

troller automatically switches the heating circuit off = Summer mode.

If the outdoor temperature drops below this value, the heating circuit is switched on

again = Winter mode.

Settings range: 0°C to 30°C / Default: 12°C

5.1 Su/Wi Day

5.2 Su/Wi Night

Caution

In addition to the operating times in normal daytime operation, this setting is

also valid for times with activated comfort temperature boost and activated

low-rate period boost.

«
...
18
19
20
21
22
...
»

Содержание HCC 4





































Отзывы:

Нет отзывов