Sorel HCC 4 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

Sorel HCC 4 Скачать руководство пользователя страница 26

26

Protective functions

7.

Protective functions

Menu “7. Protective functions” can be used

by specialists to activate and set various

protective functions. The menu is closed by

pressing “esc” or selecting “Exit settings”.

This does not under any circum-

stances replace the safety facilities

to be provided by the customer!

Caution

Switching the frost protection function off or setting the minimum flow

temperature too low can lead to severe damage of the system.

Caution

If the anti-seizing protection is activated, the controller switches the heat pump and the

mixer on/off at 12:00 pm for 5 seconds to prevent seizing of the pump/valve after long

periods of inactivation.

Settings range: on, off/ Default: on

Frost protection function can be activated for the heat circuit. If the outdoor temperature

at sensor S1 drops below 1 °C and the heat circuit is switched off, the controller swit

-

ches the heat circuit back on with the reference temperature set in in menu 7.3 (min.

flow temperature). As soon as the outdoor temperature exceeds 1°C the heat circuit is

switched off again.

Frost protection - settings range: on, off / Default: on

The minimum flow temperature is the lower limit for the characteristic curve/slope and

as a result of the reference flow temperature of the heat circuit. Additionally, the min.

flow temperature is the reference flow temperature for the frost protection.

Settings range: 5°C to 30°C / Default: 15°C

7.1 Anti-seizing protection

7.2 Frost protection

7.3 min. flow temperature

«
...
24
25
26
27
28
...
»

Содержание HCC 4





































Отзывы:

Нет отзывов