Sorel HCC 4 Скачать руководство пользователя страница 22

22

Settings Heating circuit

Caution

The following settings can be used for parallel translation of the characte

-

ristic for certain time periods such as daytime and nighttime mode.

Parallel translation of the characteristic curve

The day correction produces a parallel translation of the heating characteristic during 

the daytime operating hours, since depending on the outdoor temperature it is possible 

that the building may not be optimally heated with the set characteristic. If the charac

-

teristic is not optimised, the following situation may occur: in hot weather - the spaces 

are too cold in cold weather - the spaces are too hot In this case, one should gradually 

reduce the characteristic slope in steps of 0.2, each time raising the day correction by 

2-4 °C. This procedure can be repeated several times as needed.

Setting range: from -10°C to 50°C / default setting: 5

5.4  Day correction

Parallel translation of the characteristic curve

The night correction produces a parallel translation of the heating characteristic during 

the nighttime operating hours. If a negative value is set for the night correction, the re-

ference fl ow temperature is lowered accordingly during the nighttime operating hours. 

In this manner, primarily at night, but also during the day when no-one is at home, the 

room temperature is lowered, thus saving energy. 

Example: A day correction of +5°C and a night correction of -2°C produces a reference 

fl ow temperature in nighttime operation that is 7°C lower. 

Setting range: from -30°C to 30°C / default setting: -2°C

5.5  Night correction

Parallel translation of the characteristic curve

The comfort temperature boost is added to the set day correction. In this manner it is 

possible to carry out quick heating and/or a higher temperature in the living spaces at a 

certain time each day.

Setting range: from 0°C to 15°C / default setting: 0°C = off

5.6  Comfort temperature boost

Содержание HCC 4





































Отзывы: