Sony DCR-IP45 - Micromv Digital Camcorder, Руководство по обслуживанию

Страница: 96 / 153

5-30
DCR-IP45/IP45E/IP55/IP55E
15. Strobe Light Level Adjustment
Adjust the light level when the strobe light flashes.
Subject Paper which reflection rate is 18%
(50cm from the front of the lens) (Note1)
Measurement Point Adjustment remote commander
Measuring Instrument
Adjustment Page F
Adjustment Address 8C to 91
Specified Value Data of page: 6, address: B8 is “00”.
Note1: Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2: Any light other than the strobe light should not light up the paper.
Note3: This adjustment should be carried out upon completion of “HALL
Adjustment” , “Flange Back Adjustment”.
Note4: The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 7 05 04 Set the data. (Note6)
3 6 01 67 Set the data, and press PAUSE
button.
4 Check the flashing.
5 6 02 Check that the data is “01”.
(Note7)
6 6 B8 Check that the data is “00”.
Note6:
Use the STOP button of the adjustment remote commander.
Note7: The adjustment data will be automatically input to page: F, address:
8C to 91.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSE
button.
2 7 05 00 Set the data.
3 0 01 00 Set the data.
16. Strobe White Balance Adjustment & Check
Adjust and check the white balance when the strobe light flashes.
Subject Paper which reflection rate is 18%
(50cm from the front of the lens)
(Note1)
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Adjustment Page F
Adjustment Address 3E, 3F
Specified Value Fig. 5-1-13.
Note1: Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2: Any light other than the strobe light should not light up the paper.
Note3:
This adjustment should be carried out upon completion of “HALL
Adjustment”, “Flange Back Adjustment”, “Auto White Balance
& LV Standard Data Input”, “Auto White Balance Adjustment”,
“Strobe Light Level Adjustment”
Note4: The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 7 05 04 Set the data. (Note6)
3 6 01 B9 Set the data, and press PAUSE
button.
4 Check the flashing.
5 6 02 Check that the data is “01”.
(Note7)
6 6 02 00 Set the data.
7 6 01 E7 Set the data, and press PAUSE
button.
8 Check the flashing.
9 6 02 Check that the data is “01”.
10 Wait for 3 sec.
11 Check that the center of the
white luminance point is within
the circle shown Fig. 5-1-13.
Note6:
Use the STOP button of the adjustment remote commander.
Note7: The adjustment data will be automatically input to page: F, address:
3E, 3F.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSE
button.
2 7 05 00 Set the data.
3 0 01 00 Set the data.
Fig. 5-1-13.
R-Y 2mm
B-Y
2mm