Sony DCR-IP45 - Micromv Digital Camcorder, Руководство по обслуживанию

Страница: 116 / 153

5-50
DCR-IP45/IP45E/IP55/IP55E
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Initialization of 4, 8, 9, A, B, C, D, E, F, 1B, 1E, 1F
Page Data
If the 4, 8, 9, A, B, C, D, E, F, 1B, 1E, 1F page data is erased due to
some reason, perform “1-2. INITIALIZATION OF 4, 8, 9, A, B, C,
D, E, F, 1B, 1E, 1F PAGE DATA”, of “5-1. CAMERA SECTION
ADJUSTMENT”
Note: When reading or writing the 1B, 1E, 1F page data, select page: 0,
address: 10, and set data: 01, then select B, E or F page. The 1B. 1E
or 1F page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
2. Touch Panel Adjustment
Adjust the calibration of the touch panel.
Mode VTR stop
Signal Arbitrary
Adjusting method:
1) While pressing the DISPLAY button, set the POWER switch
from OFF to VCR.
2) Using a stylus, push the center of “X” indicated in the part A.
3) Using a stylus, push the center of “X” indicated in the part B.
4) Using a stylus, push the center of “X” indicated in the part C.
Fig. 5-3-4.
3. Serial No. Input
Write the serial No. and model code in the EEPROM (nonvolatile
memory). Convert the serial No. on the name plate from decimal to
hexadecimal, and write in the EEPROM.
Note:
The data of page: 0, address: 10 must be “00”.
Page 9
Address 09, 0A, 0B
Input method:
1) Select page: 0, address: 01, and set data: 01.
2) Read the serial No. on the name plate, and take it as D
1
.
Example: If the serial No. is 77881.
D
1
=77881
Note: Use six digits of the low rank when a serial No. is more than
seven digits.
3) Obtain D
2
and H
1
corresponding to D
1
from Table. 5-3-2.
Example: If D
1
is “77881”.
D
2
=D
1
-65536=12345
H
1
=FE
Table. 5-3-2.
4) Input H
1
to page: 9, address: 09. (Model code input)
Example: If H1 is “FE”.
Select page: 9, address: 09, set data: FE, and press the
PAUSE button.
5) Obtain the maximum decimal not exceeding D
2
from Table. 5-
3-3., and take this as D
3
.
Example: If D
2
is “12345”.
D
3
=12288
6) Obtain the hexadecimal corresponding to D
3
from Table. 5-3-
3., and take this as H
3
.
Example: If D
3
is “12288”.
H
3
=3000
7) Obtain the difference D
4
between D
2
and D
3
. (Decimal
calculation, 0 D
4
255)
D
4
= D
2
–D
3
Example: If D
2
is “12345” and D
3
is “12288”.
D
4
=12345–12288=57
8) Convert D
4
to hexadecimal, and take this as H
4
.
(Refer to “Hexadecimal-decimal conversion table” in “5-4.
Service Mode”.)
Example: If D
4
is “57”.
H
4
=39
9) Input the upper 2 digits of H
3
to page: 9, address: 0A.
Example: If H
3
is “3000”.
Select page: 9, address: 0A, set data: 30, and press the
PAUSE button.
10) Input H
4
to page: 9, address: 0B.
Example: If H
4
is “39”.
Select page: 9, address: 0B, set data: 39, and press the
PAUSE button.
11) Select page: 0, address: 01, and set data: 00.
D
1
(Decimal)
000001 to 065535
065536 to 131071
131072 to 196607
D
2
(Decimal)
D
1
D
1
–65536
D
1
–131072
H
1
(Hexadecimal)
(Service model code)
FE
FE
FE
A
C
B