Sony Ericsson GM-41 Phase II Скачать руководство пользователя страница 13

Страница: 13 / 51

Confidential
MANUAL

13(51)

Document number

Revision

7/198 17-LXE 108 566 Uen

Note: Any hard copy of this document is for reference only.

Due to template and application dependencies the header and footer may fail to display correct data. It is the

responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

2.3.2 Power Signals

•

VCC_MAIN

•

VCC_AUX

•

VRTC

•

GND

VCC_MAIN and VCC_AUX can be supplied from the same regulator, or from separate supplies. For more
information see “

Recommended Application Circuitry

”.

2.3.2.1 VCC_MAIN

Limits

Parameter

Symbol

Condition

Minimum

Nominal

Maximum

Units

Normal SIM

4.5

5.0

5.5

Extended SIM-cable driver

4.9

5.0 5.5

Volt

0 – 4kHz

100

ripple

>4kHz

In-rush current when

applying power

Supply ESR = 110m

Ω

15.0

In-rush current when

setting

MODULE_PWR_EN_B

active

3.0

During a call

100

Sleep-mode 2.0

4.5

6.0

Sleep-mode

Extended SIM-cable driver

4.0 6.5 8.0

RMS

VCC_MAIN

Baseband

and receiver

supply

voltage.

Power Down

0.1

Table 4: VCC_MAIN Electrical Parameters

The minimum voltage level is increased from 4.5 to 4.9 if the application is using a module capable of driving long

cables (up to 8 meters) and is expected to be used with 5V SIM-cards.

In-Rush current specified in VCC_MAIN combines both VCC_MAIN and VCC_AUX.

Содержание GM-41 Phase II




















































Результаты поиска

Содержание GM-41 Phase II

Отзывы:

Похожие инструкции для GM-41 Phase II

Бренды по названию

Популярные бренды

Sony Ericsson GM-41 Phase II, Руководство интегратора

Результаты поиска

Содержание GM-41 Phase II

Отзывы:

Похожие инструкции для GM-41 Phase II

Бренды по названию

Популярные бренды