Sony Ericsson GM-41 Phase II Скачать руководство пользователя страница 51

Страница: 51 / 51

Confidential
MANUAL

51(51)

Document number

Revision

7/198 17-LXE 108 566 Uen

Note: Any hard copy of this document is for reference only.

Due to template and application dependencies the header and footer may fail to display correct data. It is the

responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

7 Technical Data

Mechanical specifications

Maximum length:

130.00 mm

Maximum width:

49.50 mm

Maximum thickness:

15.0 mm

Weight:

37.5 g

Power supply voltage, normal
operation

VCC_MAIN / VCC_AUX

Nominal Voltage:

5.00 Volts

Voltage range:

4.50 – 5.50 Volts

Radio specifications

EGSM

GSM

DCS

Frequency range:

TX: 880 – 890

RX: 925 - 935

TX: 890 - 915

RX: 935 - 960

TX: 1710 - 1785

RX: 1805 - 1880

Antenna impedance:

Operational VSWR (Maximum):

2:1 2:1 2:1

Maximum VSWR before damage:

8:1 8:1 8:1

Environmental specifications

Operating temperature range:

-10

C to +55

C: ETSI TS 151 010-1 VER 4_6_0

-40

C to –10

C: –3dB degradation on TX output power and

RX sensitivity, also, GM41 will not misuse frequency
spectrum.
+55

C to +85

C: –3dB degradation on TX output power and

RX sensitivity, also, GM41 will not misuse frequency
spectrum.

Storage temperature range:

-40

C to +85

Maximum relative humidity:

80% at +30

Stationary vibration, random

Power spectral density (G

/Hz):0.40, 0.1, 0.1, 0.002, 0.002,

Frequency (Hz):10, 20, 100, 800, 1000
120 min per/axis, 4.3Grms

Non-stationary vibration, including shock

•

Shock response spectrum I, peak acceleration:

- 3 shocks in each axis and direction: 20G, 11 ms

Free fall transportation:

1.0 m

Low air pressure/high air pressure:

70 kPa / 106 kPa

Table 29: Technical Data

Содержание GM-41 Phase II




















































Результаты поиска

Содержание GM-41 Phase II

Отзывы:

Похожие инструкции для GM-41 Phase II

Бренды по названию

Популярные бренды

Sony Ericsson GM-41 Phase II, Руководство интегратора

Результаты поиска

Содержание GM-41 Phase II

Отзывы:

Похожие инструкции для GM-41 Phase II

Бренды по названию

Популярные бренды