Sony Ericsson GM-41 Phase II Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 51

background image

Confidential
MANUAL

33(51)

Document number

Revision

7/198 17-LXE 108 566 Uen

A

Note: Any hard copy of this document is for reference only.

Due to template and application dependencies the header and footer may fail to display correct data. It is the

responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

3.1.1 Power Signals Recommended Circuitry

Figure 14: Recommended Power Supply

3.1.1.1 VCC_MAIN

This power supply input to the module Baseband and receiver can use the same supply as VCC_AUX.

3.1.1.2 VCC_AUX

GM-41 has no internal capacitance on VCC_AUX to supply the large current peaks during GSM burst transmission.

3.1.1.3 VRTC

If the RTC is used, the VCC_MAIN must be kept active for the RTC to be able to turn the module on. If the RTC is
expected to work for an unspecified time, it is recommended that a regulator is used to supply the VRTC. If the
RTC is to be used in intervals of 48 hours a super cap is sufficient.

3.1.1.4 GND

Tie all five signals-pins to the application main ground. This is the return path for all the module-current.

«
...
31
32
33
34
35
...
»

Содержание GM-41 Phase II




















































Отзывы:

Нет отзывов

Похожие инструкции для GM-41 Phase II

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

Бренд: Digitus Страницы: 8

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: Z-Com Страницы: 18

Бренд: NEC Страницы: 70

FireWire 800 ExpressCard 34

Бренд: LaCie Страницы: 24

airMAX NanoBridge M NBM3

Бренд: Ubiquiti Страницы: 24

SmartRack SR25UBEXP

Бренд: Tripp Lite Страницы: 4

i.MX 8M Mini LPDDR4 EVK

Бренд: NXP Semiconductors Страницы: 20

Бренд: IBM Страницы: 168

Бренд: R3 Страницы: 48

Бренд: Acromag Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды