Sony Ericsson GM-41 Phase II Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 51

background image

Confidential
MANUAL

29(51)

Document number

Revision

7/198 17-LXE 108 566 Uen

A

Note: Any hard copy of this document is for reference only.

Due to template and application dependencies the header and footer may fail to display correct data. It is the

responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

Figure 13: SMA Right Angle Through-Hole Connector

(Dimensions are in mm)

Electrical performance parameters are valid only when the terminating impedance at the output of the antenna
connector exhibits a VSWR of less than 2:1 for all phase angles in the frequency band of operation. High VSWR
loads at the antenna connector adversely affect current consumption, linearity, and power efficiency of the module
and may degrade operation; however, internal protection circuitry has been added to the design to prevent
damage.

«
...
27
28
29
30
31
...
»

Содержание GM-41 Phase II




















































Отзывы:

Нет отзывов

Похожие инструкции для GM-41 Phase II

Бренд: IEI Technology Страницы: 21

Бренд: Paradyne Страницы: 112

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

Бренд: Avolites Страницы: 24

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

Бренд: Xenteq Страницы: 16

Бренд: Maxtor Страницы: 2

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Masterliquid ML240L RGB

Бренд: Cooler Master Страницы: 18

Бренд: Intel Страницы: 20

Бренд: Kontron Страницы: 14

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

Бренд: NI Страницы: 8

Бренд: ICP DAS USA Страницы: 26

BNI EIP-508 05-Z015 Series

Бренд: Balluff Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды