manualshive.com logo in svg

SOMFY animeo DRM, Инструкция по эксплуатации

Поделиться
Скачать
SOMFY animeo DRM Скачать руководство пользователя страница 40

 animeo KNX 4 AC MoCo · REF. 5071074 - 

40/47

Basic function

Selection options: 

 

Venetian blind UP / DOWN

 

  Switch/Dry contact

 

  8-Bit value

 

  Dimming

 

  Venetian blind slow tilting

Function of the "UP" button

Selection options: 

 

On

 

  Off

 

  Toggle

 

  No function

  On

If the "my" button in the radio transmitter is pressed, the object value "On" is generated. The duration of the activity is not evaluated.

  Off

If the "my" button in the radio transmitter is pressed, the object value "Off" is generated. The duration of the activity is not evaluated.

  Toggle

If the "my" button in the radio transmitter is pressed, the object value "At" is generated. The duration of the activity is not evaluated.

  No function

If the "my" button in the radio transmitter is pressed, this is not evaluated.

Functionality of the "DOWN" button

Selection options: 

  On

 

 

Off

 

  Toggle

 

  No function

Functionality of the "my" button

Selection options: 

  1-Bit value

 

  8-Bit value

 

 

No function

For a description please see "Function of the "my" button with Venetian blind UP/DOWN".

On ("1")  Off ("0") 

Toggle ("1/0")

On ("1")  Off ("0") 

At ("1/0")

"Radio binary input 1...5"

Содержание animeo DRM
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды