SOMFY animeo DRM Скачать руководство пользователя страница 17

Страница: 17 / 47

animeo KNX 4 AC MoCo · REF. 5071074 -

17/47

The selection options of the single parameters are described in each case. The defaults are printed in italics. In the following illustrations of

the different parameter cards the maximum number of parameters is shown. Besides this and depending on the parameter settings, objects

which are not required are blended out.

6.1 Menu index card "General"

Standard settings of the motors

Selection options:



Combined



Individual

With these parameters, the settings of the motor outputs are made as to whether

"Combined"

"Individual"

. If the parameter

"Combined”

selected, only one menu index card becomes visible for the basic settings of all four motor outputs (motor 1-4).

The selection "Combined” is recommended for projects for which the settings of the motor outputs are the same.

If the parameter "Individual" is selected, four single cards become visible for the standard settings of the motor outputs (motor 1, motor 2,

…).

Selection priority automatic / manual

Selection options:



Yes

With the parameter "Yes" the settings for the priority functions become visible. At the same time the necessary objects appear.

Parameter

"General"

Содержание animeo DRM
















































Результаты поиска

Содержание animeo DRM

Отзывы:

Похожие инструкции для animeo DRM

Бренды по названию

Популярные бренды

SOMFY animeo DRM, Инструкция по эксплуатации

Результаты поиска

Содержание animeo DRM

Отзывы:

Похожие инструкции для animeo DRM

Бренды по названию

Популярные бренды