Sollae CSE-M53N Скачать руководство пользователя | Manualshive

Страница: 68 / 72

background image

CSE-M53N User Manual Ver. 2.5

Sollae Systems Co., Ltd.

- 67 -

http://www.ezTCP.com

12

Precaution and Exemption from Liability

12.1

Precaution



Sollae Systems is not responsible for product failures occurring due to user’s
alternation of the product.



Specifications of the product are subject to change without prior notice for
performance improvement.



Sollae Systems does not guarantee successful operation of the product if the
product was used under conditions deviating from the product specifications.



Reverse engineering of firmware and applications provided by Sollae Systems is
prohibited.



Use of firmware and applications provided by Sollae Systems for purposes other
than those for which they were designed is prohibited.



Do not use the product in an extremely cold or hot place or in a place where
vibration is severe.



Do not use the product in an environment in which humidity is high or a lot of oil
exists.



Do not use the product where there is caustic or combustible gas.



Sollae Systems does not guarantee normal operation of the product under the
conditions a lot of noise exists.



Do  not  use  the  product  for  a  purpose  that  requires  exceptional  quality  and
reliability relating to user’s injuries or  accidents  –  aerospace, aviation,  health  care,
nuclear power, transportation, and safety purposes.



Sollae Systems is not responsible for any accident or damage occurring while using
the product.

«
...
66
67
68
69
70
...
»

Содержание CSE-M53N









































































Отзывы:

Нет отзывов

Похожие инструкции для CSE-M53N

Бренд: EasyIO Страницы: 18

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: OEM Страницы: 8

Бренд: ABB Страницы: 102

GA Industries 930-DT

Бренд: Vag Страницы: 4

Бренд: GEA Страницы: 13

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренд: Hach Страницы: 504

Бренд: Paser Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды