Sollae CSE-M53N Скачать руководство пользователя страница 28

Страница: 28 / 72

CSE-M53N User Manual Ver. 2.5

Sollae Systems Co., Ltd.

- 27 -

http://www.ezTCP.com

Operation Modes

4.1

What is the Operation Mode?

Each of three operation mode of CSE-M53N is defined for specific purpose, and those

are followed.



Normal mode
This mode is for normal data communication and has 4 different connection modes.
Configuring parameters is also available in this mode.



Serial configuration mode
This mode is for configuring environmental parameters through the RS-232 port.



ISP mode
This mode is for upgrading firmware. In addition, you can set environmental
parameters even though the security options like password are activated by entering
this mode.

4.2

How to entering each mode

Figure 4-1 How to entering each mode

①

Put the ISP# pin into GND less than 1 second.

②

Reset or “g 0” command

③

Transfer a firmware by ezManager

④

Put the ISP# pin into GND more than 1 second.

Содержание CSE-M53N









































































Результаты поиска

Содержание CSE-M53N

Отзывы:

Похожие инструкции для CSE-M53N

Бренды по названию

Популярные бренды

Sollae CSE-M53N, Руководство пользователя

Результаты поиска

Содержание CSE-M53N

Отзывы:

Похожие инструкции для CSE-M53N

Бренды по названию

Популярные бренды