Solar Stik PSS-G Скачать руководство пользователя страница 54

Страница: 54 / 141

PSS-G/RAID Alternative Energy System Deployment Guide

August 2020

Solar Stik

Inc.

13 Install and Connect Generator Power Cable to PRO-Verter 7000

PRO-Verter 7000 AGS

5kW MEP-802A TQG

120 VAC 50 A input

Voltage/phase setting for
the MEP-802A generator
in the PSS-G/RAID AES
configuration

MEP-802A 120VAC
power-out cable

Hubbell 120VAC/50A AC power-in port

Wiring configuration for
the 120 VAC power-out
cable of the MEP-802A

a. Position the voltage/phase selector to 120V/1PH.
b. Connect the bare ends of the generator power cable to the MEP-802A (green to GND,

black to L3, and white to N) using the wrench affixed to the interior of the generator.

c. Tighten the protective cover around the cable where the cable exits from the generator.

There may be cables already attached to the MEP-802A TQG. These can remain attached as
long as the external ends are capped and protected.

d. Connect the power cable to the

120VAC/50A Hubbell port on the left side
of the PRO-Verter 7000 AGS.

Legend

AC supply power cord

Direction of flow energy or comm

Figure 50. PRO-Verter 7000 AGS to MEP-802A TQG AC power connection

Содержание PSS-G














































































































































Результаты поиска

Содержание PSS-G

Отзывы:

Похожие инструкции для PSS-G

Бренды по названию

Популярные бренды

Solar Stik PSS-G, Руководство по развертыванию

Результаты поиска

Содержание PSS-G

Отзывы:

Похожие инструкции для PSS-G

Бренды по названию

Популярные бренды