Solahart 151J Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 60

background image

ANNUAL PERFORMANCE CALCULATIONS FOR EUROPE

42

L SYSTEMS

Annual performance calculations of Solahart thermosiphon L systems with the L collector according to EN12976
SolarKeyMark Systems ITW Test Report 11SYS92-01 for the 151L (150 tank, 1 collector), 181L (180 tank, 1 collector),
and 302L (300 tank, 2 collectors) systems.

Qd = energy demand

QL = solar energy (load)

f-sol = solar fraction

Model

151L

151L

151L

151L

Demand

110 litres / day

140 litres / day

170 litres / day

200 litres / day

Location

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Stockholm

59.6°N

6107

2712

44.5

7772

3031

39.0

9438

3048

32.3

11103

3053

27.5

Wurzburg

49.5°N

5854

2816

48.1

7450

3174

42.6

9047

3248

35.9

10643

3246

30.5

Davos

46.8°N

6628

3930

59.3

8435

4319

51.2

10243

4333

42.3

12050

4338

36.0

Athens

38.0°N

4545

3504

77.1

5784

4095

70.8

7024

4418

62.9

8263

4594

55.6

Model

181L

181L

181L

181L

Demand

140 litres / day

170 litres / day

200 litres / day

250 litres / day

Location

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Stockholm

59.6°N

7772

3334

42.9

9438

3671

38.9

11103

3697

33.3

13879

3706

26.7

Wurzburg

49.5°N

7450

3457

46.4

9047

3863

42.7

10643

3927

36.9

13304

3938

29.6

Davos

46.8°N

8435

4791

56.8

10243

5234

51.1

12050

5242

43.5

15063

5257

34.9

Athens

38.0°N

5784

4361

75.4

7024

4973

70.8

8263

5313

64.3

10329

5609

54.3

Model

302L

302L

302L

302L

Demand

200 litres / day

250 litres / day

300 litres / day

400 litres / day

Location

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Qd

MJ/a

QL

MJ/a

f-sol

%

Stockholm

59.6°N 11103

5230

47.1

13879

5871

42.3

16655

6146

36.9

22206

6195

27.9

Wurzburg

49.5°N 10643

5375

50.5

13304

6093

45.8

15965

6498

40.7

21286

6577

30.9

Davos

46.8°N 12050

7628

63.3

15063

8420

55.9

18075

8766

48.5

24100

8772

36.4

Athens

38.0°N

8263

6610

80.0

10329

7695

74.5

12395

8490

68.5

16526

9271

56.1

Note: The over temperature protection tests have been carried out according to EN12976 with an irradiation higher than
20 MJ/m

2

/day. An over temperature protection device should be installed in the situation that irradiation this exposure

levels could be exceeded.

«
...
40
41
42
43
44
...
»

Содержание 151J





























































Отзывы:

Нет отзывов

Похожие инструкции для 151J

Бренд: Jet-Line group Страницы: 20

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

Бренд: Paloma Страницы: 24

Бренд: Nastec Страницы: 28

Бренд: T-MAG Страницы: 36

Бренд: I.VA.CO. Страницы: 12

Бренд: Warren rupp Страницы: 22

Бренд: esotec Страницы: 2

Silencer AP Series

Бренд: HALE Страницы: 146

Бренд: Cadet Страницы: 8

Бренд: Garland Страницы: 100

Бренд: STIEBEL ELTRON Страницы: 20

Бренд: Slant/Fin Страницы: 16

Бренд: Master Страницы: 13

Бренд: BN Thermic Страницы: 4

Бренд: SAMES KREMLIN Страницы: 49

Бренд: STIEBEL ELTRON Страницы: 96

Бренд: SKF Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды