Solahart 151J Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 60

background image

INSTALLATION INSTRUCTIONS - ALL MODELS

23

Booster Control

The isolating switch(s) installed at the switchboard and adjacent to the solar storage tank (if installed) should be left
switched on.

Leaving the isolating switch(s) switched on will also provide a sufficient period of time each day for the booster heating
unit to operate, if required, to satisfy the requirements of AS 3498.

Timer Control Switch

A suitably rated timer control switch can be installed and will help maximise energy savings with an electrically boosted
solar water heater connected to a continuous, time of use or extended Off-Peak (overnight and day) electricity supply.

If used with an extended Off-Peak (overnight and day) electricity supply, the timer switch should:

•

Be operated by a continuous power supply on its own circuit from the switchboard with the booster heating unit
operated by the Off-Peak power supply.
A double pole isolating switch is required to be installed at the switchboard to simultaneously isolate both circuits.

Or

•

Be of a type which has an internal rechargeable battery to keep time when the power supply is not available to the
timer.

Refer to

“Programming the Timer”

on page 13.

Timer Control Switch Wiring Diagram

Timer With Contactor (if required)

Timing Wiring Diagrams Electric Boosted Solar Water Heater

Continuous

Power Supply

Switchboard

Extended Off-Peak

Power Supply

Switchboard

Timer

Terminal Block

Timer Without Contactor

Timer

Terminal Block

«
...
21
22
23
24
25
...
»

Содержание 151J





























































Отзывы:

Нет отзывов

Похожие инструкции для 151J

Бренд: Jaga Страницы: 2

Бренд: Qual Craft Страницы: 5

Бренд: Parker Страницы: 44

Бренд: SAER Elettropompe Страницы: 76

Бренд: Gude Страницы: 62

Johnson Pump CombiProLine OH3

Бренд: SPX FLOW Страницы: 67

Бренд: Optimum Страницы: 11

Бренд: Toyostove Страницы: 2

Бренд: Clarke Страницы: 12

Sportline HydraCoach

Бренд: E&B Giftware Страницы: 14

Бренд: Gasmate Страницы: 8

Pilot Light Ignition

Бренд: L.B. White Страницы: 21

Flojet RLFP122202A

Бренд: Xylem Страницы: 40

Бренд: Barnstead Thermolyne Corporation Страницы: 32

Бренд: vacuubrand Страницы: 96

Бренд: COSMOGAS Страницы: 182

Бренд: Mitsubishi Страницы: 13

Бренд: Dimplex Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды