manualshive.com logo in svg

Solahart 151J, Руководство пользователя


Поделиться
Скачать
background image

 

52 

INSTALLATION CHECK LIST 

 
Prior to handover, complete the installation check list: 

1.

 

System is installed as per the installation instructions ............................................................................................ [    ] 

2.

 

Water is connected, turned on and solar storage tank is filled ............................................................................... [    ] 

3.

 

Closed circuit is filled with correct concentration of fluid and has been commissioned ........................................ [    ] 

4.

 

All mechanical fixings are secured ......................................................................................................................... [    ] 

5.

 

Collector rail has a rise of 12-15 mm per collector on the hot outlet side of the solar collectors 
if installed directly onto the roof ............................................................................................................................ [    ] 

6.

 

Collector rail is either horizontal or higher on the hot outlet side of the solar collectors if part of a frame ........... [    ] 

7.

 

In the case of a remote installation ensure a minimum DN20 or 22mm pipe is used for the solar cold  
and solar hot pipe, and the pipes have a continuous upwards slope towards the tank from the collectors ............ .[    ] 

8.

 

Protective plastic film removed from tank (if fitted) .............................................................................................. [    ] 

9.

 

Covers removed from collectors ............................................................................................................................ [    ] 

10.

 

Pipe, conduit penetrations through the roof have been sealed correctly ................................................................. [    ] 

11.

 

Roof tiles put back into position ............................................................................................................................. [    ] 

12.

 

Roof flashing watertight ......................................................................................................................................... [    ] 

13.

 

System checked for water (and heating fluid) leaks and pipe connections are correctly tightened ........................ [    ] 

14.

 

Cold and hot water piping checked for water leaks ................................................................................................ [    ] 

15.

 

Drain pipes free of any obstruction ........................................................................................................................ [    ] 

16.

 

All pipe work clipped where necessary .................................................................................................................. [    ] 

17.

 

Electrical power to the booster is switched on (if required) ................................................................................... [    ] 

18.

 

Operation of booster checked ................................................................................................................................. [    ] 

19.

 

Air bled from taps .................................................................................................................................................. [    ] 

20.

 

Instruct the householder on the water heater system use and leave manual with the householder ......................... [    ] 

 
 

Содержание 151J





























































Отзывы:

Нет отзывов

Похожие инструкции для 151J

Cadac 942 User Instructions preview
942
Бренд: Cadac Страницы: 8
Balboa GS100 Operation Manual preview
GS100
Бренд: Balboa Страницы: 2
Wacker Neuson PT Series Service Manual preview
PT Series
Бренд: Wacker Neuson Страницы: 38
CALEFFI 528 Series Instructions Manual preview
528 Series
Бренд: CALEFFI Страницы: 9
Vector 2003 Installation And Operation Manual preview
2003
Бренд: Vector Страницы: 8
Davey AS Series Installation And Operating Instructions Manual preview
AS Series
Бренд: Davey Страницы: 16
M&C MP Series Operating Instructions Manual preview
MP Series
Бренд: M&C Страницы: 18
Warm Tech CAC20KW Instructions Manual preview
CAC20KW
Бренд: Warm Tech Страницы: 54
DAY 78714 Instruction Manual preview
78714
Бренд: DAY Страницы: 51
ProMinent Sigma 2 S2Ca Operating Instructions Manual preview
Sigma 2 S2Ca
Бренд: ProMinent Страницы: 77
Suntec Wellness KLIMATRONIC HEAT SUPREME Manual preview
KLIMATRONIC HEAT SUPREME
Бренд: Suntec Wellness Страницы: 124
2VV SAVANA SAV-MIX Series Installation And Operation Manual preview
SAVANA SAV-MIX Series
Бренд: 2VV Страницы: 114
dosatron Green Line D90 GL Quick Start-Up preview
Green Line D90 GL
Бренд: dosatron Страницы: 2
Modine Manufacturing 215BTC260 Installation And Service Manual preview
215BTC260
Бренд: Modine Manufacturing Страницы: 32
Kawamoto Pump RCD-40A0.75 Instruction Manual preview
RCD-40A0.75
Бренд: Kawamoto Pump Страницы: 28
Oase SwimSkim 25 Commissioning preview
SwimSkim 25
Бренд: Oase Страницы: 76
Warmtec EGW-1000 User Manual preview
EGW-1000
Бренд: Warmtec Страницы: 60
EBARA A70W Instruction Manual preview
A70W
Бренд: EBARA Страницы: 69

Бренды по названию

Популярные бренды

Загрузить еще бренды