Sokkia iX-1001 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 177

Sokkia iX-1001 Скачать руководство пользователя страница 48

44

9. CONNECTING TO EXTERNAL DEVICES

9. Check the connection status in Wireless

Information screen. Press

[OK]

to return to

<Internet>.

A program installed on the instrument can now
communicate with an external device.

• Press

[Disconnect]

to terminate the connection.

• Press

[Confirm]

to display Wireless Information

screen and check the access point setting.



DNS server and WINS server

Domain Name Servers (DNS) are server which resolve a domain name (www.aaa.com etc.) to an IP
address and vice versa.
Windows Internet Name Service (WINS) is a server which resolves a computer name on Windows
Network to an IP address and vice versa.
Secondary servers for each server are available to resolve IP address in case of a server system down.

A program installed on the instrument can communicate with an external device by connecting to Internet via
Cellular connection.



• SIM card may not be used depending on the model, the country or the area where the instrument is

purchased.

• Some SIM cards may not be used depending on the carriers or the contact details with the carrier.
• IMEI (International Mobile Equipment Identity) may be necessary when activating your SIM card. Check the

IMEI in the screen of step 6.

• Disable the PIN code on your SIM card before using.
• After powering ON, it is necessary to wait about 5 minutes

until cellular communication is ready. The message on the
right is displayed before the cellular communication is ready.

9.5

Cellular Settings and Communication

«
...
46
47
48
49
50
...
»

Содержание iX-1001


















































































































































































Отзывы:

Нет отзывов