Sokkia iX-1001 Скачать руководство пользователя страница 166

Страница: 166 / 177

162

26. SPECIFICATIONS

Handle (Remote Control System Beam Detector)

Operable range (Slope distance when using RC-PR5A under normal atmospheric conditions

)

Standard mode

*20

to 100 m

*21

Far mode

*20

to 250 m

*22

*20

to 300 m

*21

Maximum detecting area (vertical angle)

±30° (on the basis of horizontal direction)

Remote Control System Turning operation time (RC-PR5A)

15 sec or less (until completion of rapid (single) measurement)

*20

: When there is almost no vertical interval between instrument height and the target height, the instrument

height is 1.5 m, target height is 0.10 m at a horizontal distance of 1.8 m

*21

: When the vertical interval between iX and the beam emitter of Remote Controller is no more than 20 m

*22

: When the vertical interval between iX and the beam emitter of Remote Controller is no more than 40 m

Bluetooth

wireless communication

*23

Transmission method

FHSS

Modulation

GFSK

Frequency band

2.402 to 2.48GHz

Bluetooth

profile

SPP, DUN

Power class

Class 1

Usable range

to 600 m (while in communication with RC-PR5A)

*24, 25

*23

Bluetooth

function may not be built in depending on telecommunications regulations of the country or the

area where the instrument is purchased. Contact your local dealer for the details.

*24

: No obstacles, few vehicles or sources of radio emissions/interference in the near vicinity of the

instrument, no rain.

*25

: Usage range could be shorter depending on specifications of

Bluetooth

device to communicate.

Wireless LAN communication

Communication distance

10 m (indoor condition)

*26, 27

Transmission specifications

IEEE802.11g/IEEE802.11b/IEEE802.11n

Access method

Infrastructure mode, adhoc mode

Frequency range

2,412 to 2,472MHz (1 to 11 ch)

*26

: No obstacles, few vehicles or sources of radio emissions/interference in the near vicinity of the

instrument, no rain.

*27

: Usage range could change depending on the communication conditions.

Telematics system

Cellular

3G/2G

GPS

*28

L1 (for position monitoring)

User SIM

mini-SIM (2FF) (25 X 15 X 0.76 mm)

*29

*28

: Instrument position may not be detected when mountain, building, power line, tree branch etc. block

signal reception from the satellites.

*29

: Do not use SIM card converter adaptor. Inserted adaptor may not be taken out or it may damage the

inside of the SIM card slot.

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 166 / 177

Результаты поиска

Содержание iX-1001

Отзывы: