Sokkia iX-1001 Скачать руководство пользователя страница 165

Страница: 165 / 177

161

26. SPECIFICATIONS

*11

: Time to completed Auto Pointing may be longer around elevation angle 90°, because the tilt

compensation is not in operation.

*12

:No haze, visibility over 20 km, slightly overcast (less than 30000 lx), no scintillation.

*13

: When using a reflective sheet for Auto Pointing, the size of sheet (10 to 90 mm) must be selected to

correspond to the distance being measured. Use smaller reflective sheets for shorter distances.

*14

: Figures when the Auto Pointing beam strikes within 15° of the reflective sheet target.

*15

:Figures when the Auto Pointing beam strikes within elevation and depression angle 15° of the 360°

prism.

*16

: Specifications may vary depending on the model, the country or the area where the instrument is

purchased.

Motor

Type

Direct drive by ultrasonic motor

Motion range

360

(Vertical and horizontal)

Rotation speed

*17

iX-1000 series: 150°/sec (at 20°C)
iX-500 series: 85°/sec (at 20°C)

Fine motion

Jogs

*17

: Specifications may vary depending on the model, the country or the area where the instrument is

purchased.

Guide Light

Light source

LED (red 626 nm/green 524 nm)

Visible distance range

1.3 to 150 m

*18

Visible angle range

Right and Left/Upward and Downward:± 4

(7 m/100 m)

(Brightness level is less than 80,000 lx.

*19

when right and left: within ±

4°

upward and downward: ± 3°

less than 40,000 lx.

*18

when right and

left: within ± 4°

upward and downward: ± 3 to 4°)

Resolving power at center area (width)4’ (about 0.12/100 m)
Brightness

3 levels (bright/normal/dim)

*18

: Slightly overcast, the sun is seen, and dim shadows are cast on the ground.

*19

: Clear and sunny, the sun is positioned at 50° or more, sighting the target from the instrument.

Internal memory

Capacity

1 Gbyte (includes memory for program files)

External memory

USB flash memory (up to 32GB)

Data transfer

Data input/output

Asynchronous serial, RS232C compatible

USB

USB Ver. 2.0, Host (Type A) and Client (Type miniB)

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 165 / 177

Результаты поиска

Содержание iX-1001

Отзывы: