socomec R01 Скачать руководство пользователя страница 39

Страница: 39 / 44

SUNSYS pro - SUNSYS station

- Ref.: IOMSUNMOXX00-GB 00

ENGLISH

10. TROUBLESHOOTING

10.2. INVERTER WARNINGS

• W13: High impedance to earth

Make sure the photovoltaic panel earth connection is intact

• W65: Inverter in Derating

The inverter is reducing the power dispensed to the network. Check the other alerts and/or visual warnings.

10.3. SYSTEM ALERTS

• A01: Switch-off due to external command

• A59: Switch-off due to external command

The inverter is switched off due to an external instant switch-off command. Check the external contact

• A04: Low impedance to earth

Check the photovoltaic system isolation to earth

• A05: AC dischargers triggered

Check and replace if necessary

• A06: DC dischargers triggered

Check and replace if necessary

• A07: Output contactor alerts

The output contactor status is not consistent; contact the support service

• A08: Transformer Over-temperature

Check the ventilation or air-conditioning system in the inverter room.

• A09: AC input network Rms value outside tolerated range

• A10: AC input network frequency outside frequency range

The input network is missing or insufficient (incorrect voltage and/or frequency values); if this is not due to a general network absence,
check for any disconnection of protective devices upstream of the inverter.

Check the applied voltage and frequency comply with the values set on the mimic panel.

• A15: Incorrect system configuration

Error in configuration parameters; contact the support service.

Содержание R01













































Результаты поиска

Содержание R01

Отзывы:

Похожие инструкции для R01

Бренды по названию

Популярные бренды

socomec R01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание R01

Отзывы:

Похожие инструкции для R01

Бренды по названию

Популярные бренды