background image

PUSH PRO -0120843

17

Daily Preventative Maintenance Checklist

 

Preventative Maintenance Report

 

Date: ____________________________________
Owner: ___________________________________
Model No:  ________________________________

Serial No: _________________________________
Serviced By:  ______________________________

Daily Preventative Maintenance Checklist

Item

Inspect For

 

Y N

 

R

 

Operator’s Manual 

In manual holder, all pages readable and intact 

Electrical System

Battery terminals 

Clean, connectors tight

Battery charge indicator

Proper operation 

Battery charger

Proper operation 

Cables and wiring harness

No wear or physical damage

Hydraulic System

Fluid level  

Between full and add marks with platform 

stowed 

Hoses, tubes and fittings

No leaks, all fittings tight

 

 

Castors

Good condition, no damage/smooth movement

Manual Brakes

Proper operation, no damage or deformation

Lower Control Station

Operating controls

Proper operation

Emergency stop

Shuts off lower controls/proper operation

Lowering alarm and interrupt

Sounds when platform lowers/proper operation 

Emergency Lowering

 

Proper operation

 

Safety Prop

No damage or deformation

Structures

Weldments – Scissors, chassis, steps, 

platform, etc. 

Welds intact, no damage or deformation 

Platform slide rollers

 

In place, no damage or deformation 

Fasteners

In place, tight, and no damage

Scissor and Cylinder pins

Securly in place, no damage or corrosion

Upper Control Station

Guardrail system

 

Welds intact, no damage or deformation
All fasteners in place, no loose or missing parts

Platform floor 

No damage or deformation

 

Clean to prevent slip and fall hazards

Lanyard anchors

In place, no deformation or damage

Entry gate

 

Proper operation, no damage or deformation

 

Operating controls

Proper operation/raise and lower

Lowering delay

Proper operation, limit switch delays lowering

Emergency stop

Shuts off upper controls

Operation and Safety Decals 

In place and readable

Maintenance Table Key: Y = Yes/Acceptable, N = No/Not Acceptable, R = Repaired/Acceptable

 

Содержание S3006P


























Отзывы: