background image

 SMCSD10-Z Smoke Detector Guide 

 

Copyright 

©

2013 SMC Networks

  

Page 2 

                                                                                                                

All Rights Reserved 

I/M SMCSD10-Z rev. 1.0 

6/18/13 

When mounting the SMCSD10-Z on a wall, place 
it so the top is 4 to 12 inches (10 to 31cm) below 
the ceiling. 

In rooms with sloped, peaked, or gabled ceilings, 
place the SMCSD10-Z 3 feet (.9 m) down or away 
from the highest point of the ceiling. 

If mounting to suspended ceiling tile, secure the 
tile with the appropriate fastener to prevent tile 
removal. 

Smoke detectors are not to be used with alarm 
guards unless the combination has been 
evaluated and found suitable for that purpose. 

Note:

 

A smoke detector does not provide 

warnings for fires resulting from explosions, 
smoking in bed or other furniture; ignition of 
flammable liquids, vapors and gasses; and children 
playing with matches or lighters. 

Locations to Avoid 

 

Areas where normal ambient temperature 
exceeds 100° F (37.8° C). 

 

Dirty, dusty, insect infested areas. 

 

In or near areas with combustion particles 
(kitchens, garages, furnaces, hot-water 
heaters, gas space heaters). 

 

On the ceiling in rooms next to kitchens, 
where there is no transom between the 
kitchen and such rooms. 

 

Damp or humid areas, or near bathrooms 
with showers. 

 

Near fresh-air inlets or returns or very drafty 
areas. 

 

Near heating/air conditioning vents, fans, 
and fresh air intakes, which can drive smoke 
away from the smoke alarm. 

 

In dead-air spaces at the top of peaked 
ceilings or in corners where walls and ceiling 
meet. Dead air can prevent smoke from 
reaching a smoke detector. 

 

Within 10 feet (3 m) of fluorescent light 
fixtures. 

 

Not suitable for outdoor use. 

WARNING! LIMITATIONS OF SMOKE 
DECTECTORS 

The SMCSD10-Z Smoke Detector does not contain 
a built-in audio alarm. It is not intended for 
stand-alone use; it MUST be used with an 
approved Touchscreen.  

Wireless smoke detectors are very reliable, but 
may not work under all conditions. No fire alarm 
product provides total protection of life or 

property. Smoke detectors are not a substitute 
for life insurance. 
Smoke detectors require a source of power to 
work. 

This smoke detector does not operate and the 
alarm will not sound if batteries are dead or not 
installed properly. 
This SMCSD10-Z relies on the Touchscreen Alarm 
to sound an audible alarm in case of fire. The 
alarm may not be heard. A sound sleeper or 
someone who has taken drugs or alcohol may not 
awaken if Touchscreen is installed outside a 
bedroom. Closed or partially closed doors and 
distance can block sound. This product is not 
designed for the hearing impaired. 

Smoke detectors may not always activate and 
provide warning early enough. Smoke detectors 
only activate when enough smoke reaches the 
product’s smoke chamber. If a fire starts in a 
chimney, wall, roof, on the other side of closed 
doors, or on a different level of the property, 
enough smoke may not reach the product for it 
to alarm. 

Smoke detectors are a significant help in 
reducing loss, injury and even death. However, 
no matter how good a detection device is, 
nothing works perfectly under every 
circumstance and we must warn you that you 
cannot expect a smoke detector to ensure that 
you will never suffer any damage or injury.

Содержание SMCSD10-Z












Отзывы: