System Sensor BEAM1224 Скачать руководство пользователя страница 1

Страница: 1 / 18

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEAM1224, BEAM1224S
Single-ended Reflected Type
Projected Beam Smoke Detector

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

D400-73-00 1 I56-2294-03R

Specifications
General

Range:

16 to 230 Feet (5 to 70m)

230 to 328 Feet (70 to 100m) using optional accessory BEAMLRK

Sensitivity:

25% to 50% Total Obscuration in 6 levels

Level 1 = 25%

Level 2 = 30%

Level 3 = 40%

Level 4 = 50%

Level 5 = 30% to 50% (Acclimate)

Level 6 = 40% to 50% (Acclimate)

Spacing:

30 to 60 Feet (9.1 to 18.3m)

Response Time:

Alarm: 20 seconds typical

Trouble: 30 seconds typical

Trouble Conditions:

Beam Blockage (96% or More Obscuration)

Improper Initial Alignment

Self-compensation limit reached (service needed)

In Alignment mode

Test/Reset Features:

Integral Sensitivity Test Filter (BEAM1224S only)

Sensitivity Filter (Incremental scale on reflector)

Local Alarm Test Switch

Local Alarm Reset Switch

Remote Test and Reset Switch Capability

(compatible with RTS451/RTS451KEY)

Indicators:

Alarm:

Remote Output, Local LED (red)

Trouble:

Remote Output, Local LED (yellow)

Blink Pattern Indicates Trouble Diagnostics

Normal Operation:

Local LED (flashing green once every 5 sec.)

Alignment Aids:

Optical Gunsight (coarse adjustment)

00 to 99 Digital Display (fine adjustment)

Relays:

Alarm; Trouble

Sensitivity:

Digital Display Readout in Percent Obscuration

Environmental

Temperature:

–22°F to 131°F (–30°C to 55°C)

Note: For applications below 32°F (0°C), see Special Applications section of this manual

Humidity:

10% to 93% RH Noncondensing

Mechanical

Shipping Weight:

Complete unit: 3.9 lbs. (1.77 kg)

Shipping Size:

″

10.5

″

6.5

″

(381mm

267mm

165mm)

Mounting:

Wall only without optional accessories

Wiring:

Plug-in Terminal Blocks (12 to 22AWG)

Adjustment Angle:

±10° Horizontal and Vertical

Paintable Trim Ring:

May be painted using enamel or acrylic type paints

Содержание BEAM1224



















Результаты поиска

Содержание BEAM1224

Отзывы:

Похожие инструкции для BEAM1224

Бренды по названию

Популярные бренды

System Sensor BEAM1224, Инструкция по установке и обслуживанию

Результаты поиска

Содержание BEAM1224

Отзывы:

Похожие инструкции для BEAM1224

Бренды по названию

Популярные бренды