background image

NOTE:

   If the outer aesthetic ring has been painted insure 

that the paint is completely dry before proceeding 
with this step.

Step 4. Final Verification

This step is required to insure the detector has been setup 
correctly  and  will  detect  smoke  at  the  proper  sensitivity 
level.

1.  With  the  detector  functioning  (indicated  by  the  green 

LED  blinking),  completely  block  the  reflector  with  an 
opaque material. (Due to the high optical efficiency of 
the  reflector  the  selection  of  the  opaque  material  used 
to block the reflector is not critical. Acceptable materials 
include, but aren’t limited to, this manual or the card-
board  packaging  inserts.)  See  Figure  14.  The  detector 
should  enter  the  trouble  condition  (indicated  by  the 
fault relay and the yellow LED (see Appendix I). If the 
detector does not enter the trouble condition there is a 
problem with the installation refer to the troubleshoot-
ing section in Appendix I for further assistance.

2.  Complete a sensitivity test of the detector. Refer to the 

Sensitivity Testing section of this manual for the appro-
priate procedure.

3.  If the orange sticky paper was used to aid in the loca-

tion of the reflector in the alignment mirror it should be 
removed now. It is no longer necessary.

Congratulations. You have completed the final installation 
and alignment procedure.

Figure 10. Switch Locations

ALIGNMENT

SENSITIVITY

TEST

RESET

C0274-00

Figure 11. Alignment Adjustment Locations

ALIGNMENT MIRROR

ALIGNMENT GUNSIGHT

DIGITAL SIGNAL
STRENGTH
READOUT

HORIZONTAL
ADJUSTMENT

VERTICAL
ADJUSTMENT

OPTICS
LOCK-DOWN
SCREWS

ALIGNMENT
POSITION
INDICATOR

C0264-00

Figure 12. Coarse Alignment Procedure

EYE

REFLECTOR

C0625-00

D400-73-00                                                                                             10                                                                                           I56-2294-03R

Содержание BEAM1224



















Отзывы: