SMC Networks EX600-AX Скачать руководство пользователя страница 26

Страница: 26 / 73

- 26 -

No.EX##-OML0007

▪

EX600-DXPC

▪

EX600-DXNC

Note

Be sure to place a seal cap on any unused connectors.

Placing the seal cap appropriately enables the unit to achieve IP67 protection.

Handling care.

Please note the following points when using the open circuit detection function.

Open circuit detection setting can only be carried out by using a hand-held terminal. Setting cannot be
carried out using a PLC.

When a 2-wire type sensor, such as a contact sensor is used, during OFF state, a leakage current of max.
0.5 mA will not be detected. A sensor with a leakage current of min. 0.5 mA (in the OFF state) must be
used.

When a 3-wire type sensor is used, if the sensor has a current consumption of max. 0.5 mA, an open
circuit may not be detected.

Error display

Status LED displays the power supply and operation status. These can be checked according to the following:

LED

Status

Descriptions

OFF

Power supply for control and input is OFF, or input device is
OFF.

Green light ON

Input device is ON.

Flashing red

Either of the following:

Input device ON/OFF count has exceeded the set value.

Input device not connected (for open circuit detection type
only).

All LEDs flashing

Red/green alternately

Component failure inside the digital input unit.
Stop using the product and contact SMC.

Red light ON

(Both adjacent LEDs

ON)

Without open circuit detection

Short circuit in power supply of either input device “0”or “1”.

Check which input device has caused the short circuit.

Red light ON

(only one LED is ON)

With open circuit detection
Short circuit in power supply of input device "0".

Содержание EX600-AX










































































Результаты поиска

Содержание EX600-AX

Отзывы:

Похожие инструкции для EX600-AX

Бренды по названию

Популярные бренды

SMC Networks EX600-AX, Руководство по эксплуатации

Результаты поиска

Содержание EX600-AX

Отзывы:

Похожие инструкции для EX600-AX

Бренды по названию

Популярные бренды