background image

01/04/2020

3/20

E_MH_Mounting_instructions_Skylux_Cintralux_Alu_25mm_fixed_parts_flat_curb

Sharp objects
•  Make sure your fingers/hands are not pinched and watch out for cuts while handling skylights  

  or barrel vaults.

•  Be careful where you put your hands during the installation.

•  Wearing cut-resistant gloves is mandatory.  

Ergonomics
•  Always lift loads correctly: bend your knees, move your feet instead of forcing your spine, lift  

  as close to your body as possible.  

•  Parts of more than 25 kg must be lifted with at least 2 persons.

 

Personal protective equipment

•   Work clothes, safety shoes and helmet are mandatory for everyone.

•   Lifeline and harness are mandatory if the edge is not secured enough or if there are no safety nets below the   

  roof opening. They are also necessary when using an aerial working platform.

•   Use gloves when handling skylight or barrel vault parts. 

•   BSafety glasses and hearing protection are mandatory when using saws / grinders.

Always perform a Last Minute Risc Analysis!

If in doubt: STOP! Do not take unnecessary risks. Ask your supervisor if needed.

Содержание Cintralux alu 25 mm





















Отзывы: