sitrex Action 120 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

sitrex Action 120 Скачать руководство пользователя страница 37

Round Baler ACTION 120

USE AND MAINTENANCE MANUAL - 37 -

DANGER

Keep  lubricants,  oils,  solvents  and  paints  out
of  the  reach  of  children.  Carefully  read  the
warnings  and  precautions  indicated  on  the
containers of the liquids used.
After use, wash thoroughly.
Treat  used  oils  in  accordance  with  the
provisions of anti-pollution law.
You  can  find  the  oils  and  lubricants
recommended  for  the  various  parts  in  the
table below.

Part

Lubricant

Q.ty

Hydraulic

system

ENI

MULTITECH

15W-40

2

– 4 L

Chains

lubrications

ISO

– VG 100

4 L

Gearbox

SAE.140EP

2.4 L

Greasing

system

MAX NLGI 2

Look at the

table

Below there are the lubrication points found in the
machine, indicated with the appropriate stickers.

6.11 EXTRAORDINARY

MAINTENANCE

The  extraordinary  maintenance  operations  must
be  carried  out  by  expert  staff  well  trained.  The
manufacturer  is  available  to  give  information  or
explanation  on  what  to  do  in  case  of  repair  or
maintenance.

6.11.1 Lifting through hydraulic jacks

To  carry  out  the  operations  of  substitution  of  the
tires  or  intervention  on  the  axle,  may  be
necessary to lift the rear part of the round baler.
If  no  cranes  are  available  for  lifting  using  the
upper  lifting  points,  it  is  possible  to  lift  the  rear  of
the baler using one or two jacks positioned under
the framework of the axle.
Before  use,  make  sure  that  the  lifting  capacity  of
the  jacks  is  adequate  for  the  weight  of  the
machine (par. 1.7).

DANGER

It is absolutely forbidden to lift the baler using
jacks to a height of over 10 cm. As this can
lead to loss of stability of the machinery and
heavy loads on the support bracket.

«
...
35
36
37
38
39
...
»

Содержание Action 120













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды