Sirona SIROLaser Xtend Скачать руководство пользователя страница 17

Страница: 17 / 78

Sirona Dental Systems GmbH
Operating Instructions SIROLaser Xtend

3 System description

3.4 Symbols and abbreviations

63 18 351 D3576
D3576.201.01.05.02 11.2018

After upgrade

SIROLaser Xtend

= 970 nm ± 15nm

= 10 W

= 635 - 650 nm

= 1 mW

IEC 60825-1:2007

max

= 970 nm ± 15nm

= 14 W

= 635 - 650 nm

= 1 mW

IEC 60825-1:2007

max

Specification of laser output power and wavelength of IR and aiming
beam, see also chapter "Technical data" [→ 19].

CAUTION

CLASS 4 VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. AVOID EYE

OR SKIN EXPOSURE TO DIRECT

OR SCATTERED RADIATION

Warns of potential laser radiation hazards when opening the laser unit.

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION.

AVOID EYE OR SKIN EXPOSURE TO

DIRECT OR SCATTERED RADIATION

CLASS 4 LASER PRODUCT

Warns of Class 4 laser radiation hazards when using the unit.

Warns of laser radiation emission at the distal tip of the handpiece.

FINGER SWITCH

Warns of laser radiation hazards when the fiber connector is
unscrewed.

Laser Stop

"Laser Stop" key: press this button in case of an emergency

Use only with power supply

Sinpro MPU 100-106

Operate the unit exclusively with the Sinpro MPU100-106 power supply

134°C

The disassembled handpiece sleeves and the fibers may be sterilized
only in autoclaves with saturated water vapor at minimum sterilization
values of 134°C (273.2°F), 3 min. holding time and 2.04 bar (29,59 psi)
overpressure.

Single use only for the bendable tip

Refers to directive 2002/96/EC and EN 50419
Do not dispose with domestic waste

Содержание SIROLaser Xtend















































































Результаты поиска

Содержание SIROLaser Xtend

Отзывы:

Похожие инструкции для SIROLaser Xtend

Бренды по названию

Популярные бренды

Sirona SIROLaser Xtend, Руководство по эксплуатации

Результаты поиска

Содержание SIROLaser Xtend

Отзывы:

Похожие инструкции для SIROLaser Xtend

Бренды по названию

Популярные бренды