Singular Sound AEROS Скачать руководство пользователя страница 31

Страница: 31 / 36

AEROS Loop Studio: Manual

MIDI Compatability

AEROS is set to respond to MIDI messages sent on ALL channels. Making the

AEROS respond to only one speciﬁc MIDI channel is coming soon.

AEROS passes through all MIDI commands it receives in the MIDI In port to the

MIDI Out port.

Currently AEROS responds to these MIDI commands:

Sysex:

Start/Stop

MIDI Clock:

AEROS may take a few seconds to adjust to an incoming MIDI clock

signal when starting a new song

Time Signature:

This is sent by BeatBuddy whenever a song is loaded as a

Sys-ex midi message.

(All values in hex)

(2/4) ---- F0 7F 7F 03 02 04 02 02 18 08 F7

(3/4) ---- F0 7F 7F 03 02 04 03 02 18 08 F7

(4/4) ---- F0 7F 7F 03 02 04 04 02 18 08 F7

(6/8) ---- F0 7F 7F 03 02 06 03 02 18 08 F7

CC-102 (value 0-127):

Next Part command changes song parts in 2x2

immediately. In 6x6, it will change song parts if a diﬀerent song part than the

one currently playing is selected. Please note: This command overrides the

‘Change Parts: End of Loop’ setting.

CC-127 (value 127)

will save a screenshot of the current AEROS screen to the SD

card. Note: must have SD card

More MIDI command responsiveness is coming soon.

Currently, the AEROS does not generate it’s own MIDI clock or MIDI commands.

This feature is coming soon.

Содержание AEROS





































Результаты поиска

Содержание AEROS

Отзывы:

Бренды по названию

Популярные бренды

Singular Sound AEROS, Руководство пользователя

Результаты поиска

Содержание AEROS

Отзывы:

Бренды по названию

Популярные бренды