manualshive.com logo in svg

Singular Sound AEROS, Руководство пользователя

Поделиться
Скачать
Singular Sound AEROS Скачать руководство пользователя страница 24

23

AEROS Loop Studio: Manual

Settings

 

 

 

SETTINGS

Sync Track Features

●

 Definition: “Base Track”: The current longest loop in the song part

●

 Sync Length: After 1st track is recorded, all tracks will be forced to be  

   proportional to the length of the base track. In quantized mode, all         

   tracks will be forced to be any whole number multiple (x2, x3, x4, etc.)  

   or whole number unit fraction (1/2, 1/3, 1/4, 1/5, etc) of the base track.  

   For example, if the base track is 12 measures long, other tracks will be  

   forced to be either 1, 2, 3, 4, 6, 12, 24, 36, etc. measures long 

   depending on when the end recording/start playback command is    

   given. In freeform, all tracks will be whole number multiples of the    

   base track (no fractions allowed). Tracks can be started at next 

   measure in quantized mode, or immediately in freeform, so this only  

   affects when recording stops and playback begins.

●

 Sync Start & Length: In addition to the Sync Length rules above, after  

   1st track is recorded in a song part, all new recordings will begin at    

    the next start of the base track loop.

Quantize to measure: 

Starts and ends recording at the beginning/end 

of the measure. This requires a BPM and time signature setting (With 

BeatBuddy connected [MIDI Sync On], BPM and Time Signature will be 

set automatically). If this is off, song will be in Freeform (non-quantized) 

mode. 

Time Signature:

 The left number is how many beats in a measure, the 

right number decides which note gets the beat (quarter notes, eighth 

notes, etc)

Tempo:

 Speed of the song. How many beats per minute (BPM).

Count in:

 How many measures of clicks before the AEROS begins 

recording. Count in is only active when recording the first track in a 

song part while AEROS is stopped.

Содержание AEROS





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды