Sime MURELLE PRO HE MkII Скачать руководство пользователя страница 11

Страница: 11 / 72

1.2

Preliminary checks

WARNING

– Should it be necessary to access the areas in the

bottom part of the appliance, make sure that the

system components and pipes are not hot (risk of

burning).

– Before replenishing the heating system, put on pro-

tective gloves.

Prior to use the

Murelle Pro HE MkII

boiler must be installed

and commissioned by a Gas Safe Registered engineer. It may be

necessary for the user to occasionally have to start the boiler,

for instance after a holiday or after an interruption of the gas

supply. In these cases the following operations must be carried

out.

– check that the gas isolation and water system valves are open

– using the pressure gauge (1) check that the pressure in the

heating system, when cold, is

1-1.2 bar

. If the pressure is less

than this, use the external filling device to repressurise the

system to

1-1.2 bar

– ensure that the filling device is turned off after use.

Fig. 2

1.3

Ignition

After having carried out the preliminary checks, proceed as fol-

lows:

– set the main system switch to "ON"

– on the display, check that the operating mode on the display

is "SUMMER”

and if necessary select it by pressing and

holding the button

for at least 1 second. The internal tem-

perature of the boiler will appear on the display

– open one or more than one hot water tap. The

should ap-

pear on the display and the boiler will ignite and stay alight

until the tap is turned off.

Once the boiler has been operated in "SUMMER mode"

"WINTER mode"

can be selected by pressing and holding

the button

for at least 1 second. The internal temperature of

the boiler will appear on the display. Ensure that any timers and

room thermostats are in the on position. The

will appear on

the display and the boiler will ignite.

1.4

Adjusting the delivery temperature

The temperature of the heating water can be adjusted by turn-

ing the

knob on the control panel.

Fig. 3

1.5

Adjusting the domestic hot water temper-

ature

The temperature of the domestic hot water can be adjusted by

turning the

knob on the control panel.

Fig. 4

Содержание MURELLE PRO HE MkII









































































Результаты поиска

Содержание MURELLE PRO HE MkII

Отзывы:

Похожие инструкции для MURELLE PRO HE MkII

Бренды по названию

Популярные бренды

Sime MURELLE PRO HE MkII, Инструкция для пользователя, по установке и обслуживанию

Результаты поиска

Содержание MURELLE PRO HE MkII

Отзывы:

Похожие инструкции для MURELLE PRO HE MkII

Бренды по названию

Популярные бренды