Sime MURELLE PRO HE MkII Скачать руководство пользователя страница 7

Страница: 7 / 72

RANGE

MODEL

CODE

GAS COUNCIL

NUMBER

Murelle Pro HE 30 MkII

8114223

47-283-81

Murelle Pro HE 35 MkII

8114248

47-283-85

COMPLIANCE

Our company declares that

Murelle Pro HE MkII

boilers comply

with the following directives:

– Gas Appliances EU Regulation 2016/426

– Boiler Efficiency Directive 92/42/EEC

– Low Voltage Directive 2014/35/UUE

– Electromagnetic Compatibility Directive 2014/30/EU

– Ecodesign Directive 2009/125/EC

– Regulation (UE) N. 811/2013 - 813/2013

– Energy Labeling Directive 2010/30/EC

NOTE: for the model Murelle Pro HE 35 MkII WRAS and ENERGY

SAVING TRUST are under certification.

1312

Please refer to the technical data plate for the serial number

and year of manufacture.

SYMBOLS

WARNING

To indicate actions which, if not carried out correctly,

can result in injury of a general nature or may dam-

age or cause the appliance to malfunction; these

actions therefore require particular caution and ad-

equate preparation.

ELECTRICAL HAZARD

To indicate actions which, if not carried out correct-

ly, could lead to injury of an electrical nature; these

actions therefore require particular caution and ade-

quate preparation.

DO NOT

To indicate actions which MUST NOT BE carried out.

CAUTION

To indicate particularly important and useful informa-

tion.

MANUAL STRUCTURE

This manual is organized as follows.

USER INSTRUCTIONS

TABLE OF CONTENTS

DESCRIPTION OF THE APPLIANCE

TABLE OF CONTENTS

INSTALLATION AND SERVICING

INSTRUCTIONS

TABLE OF CONTENTS

Содержание MURELLE PRO HE MkII









































































Результаты поиска

Содержание MURELLE PRO HE MkII

Отзывы:

Похожие инструкции для MURELLE PRO HE MkII

Бренды по названию

Популярные бренды

Sime MURELLE PRO HE MkII, Инструкция для пользователя, по установке и обслуживанию

Результаты поиска

Содержание MURELLE PRO HE MkII

Отзывы:

Похожие инструкции для MURELLE PRO HE MkII

Бренды по названию

Популярные бренды