SimCom SIM5215 Скачать руководство пользователя страница 7

Страница: 7 / 72

Smart Machine Smart Decision

Figure Index

Figure 1: SIM5215&SIM5216 functional architecture ................................................................................................... 11

Figure 2: Pin view........................................................................................................................................................... 13

Figure 3: Board to Board connector jack

（

NAIS AXK770247G

）

............................................................................... 14

Figure 4: Board to Board connector pin

（

NAIS AXK870145W

）

............................................................................. 14

Figure 5: Top dimensions (Unit: mm)............................................................................................................................. 19

Figure 6: Side dimensions (Unit: mm)............................................................................................................................ 19

Figure 7: Bottom dimensions (Unit: mm) ....................................................................................................................... 20

Figure 8: VBAT voltage drop during burst emission (GSM/GPRS) ............................................................................... 21

Figure 9: VBAT input application circuit........................................................................................................................ 22

Figure 10: Reference circuit of the LDO power supply .................................................................................................. 22

Figure 11: Reference circuit of the DCDC power supply ............................................................................................... 23

Figure 12: RTC supply from capacitor............................................................................................................................ 23

Figure 13: RTC supply from non-chargeable battery ...................................................................................................... 24

Figure 14: RTC supply from rechargeable battery .......................................................................................................... 24

Figure 15: Seiko XH414H-IV01E Charge-Discharge characteristic............................................................................... 25

Figure 16: Power on Timing Sequence ........................................................................................................................... 26

Figure 18: Power off timing sequence ............................................................................................................................ 27

Figure 19: Full modem.................................................................................................................................................... 28

Figure 20: Null modem................................................................................................................................................... 28

Figure 21: RI behaviour in NULL Modem ..................................................................................................................... 30

Figure 22: RI behaviour in FULL Modem ...................................................................................................................... 30

Figure 23: Speaker interface configuration ..................................................................................................................... 32

Figure 24: Receiver interface configuration.................................................................................................................... 32

Figure 25: Microphone interface configuration .............................................................................................................. 33

Figure 26:: Headphone Microphone interface configuration .......................................................................................... 33

Figure 27: USIM interface reference circuit ................................................................................................................... 36

Figure 28: Amphenol SIM card socket ........................................................................................................................... 37

Figure 29: Reference circuit............................................................................................................................................ 40

Figure 30: Analog sensor circuit reference...................................................................................................................... 40

Figure 31: USB interface ................................................................................................................................................ 42

Figure 32: SDIO interface circuit.................................................................................................................................... 44

Figure 33: Application circuit ......................................................................................................................................... 45

Figure 34: Flight mode switch ........................................................................................................................................ 46

Figure 35: Synchrony timing .......................................................................................................................................... 47

Figure 36: EXT CODEC to MODULE timing................................................................................................................ 48

Figure 37: MODULE to EXT CODEC timing................................................................................................................ 48

Figure 38: Synchrony timing .......................................................................................................................................... 49

Figure 39: EXT CODEC to MODULE timing................................................................................................................ 49

Figure 40: MODULE to EXT CODEC timing................................................................................................................ 49

Figure 41: Reset circuit................................................................................................................................................... 51

Figure 42: Reference circuit............................................................................................................................................ 51

Figure 43: RF adapter cable MXTK88TK2000 .............................................................................................................. 55

SIM5215&SIM5216_Hardware Design_V2.02

2012-08-31

Содержание SIM5215









































































Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды

SimCom SIM5215, Проектирование аппаратного обеспечения

Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды