manualshive.com logo in svg

SimCom SIM5215, Проектирование аппаратного обеспечения

Поделиться
Скачать
SimCom SIM5215 Скачать руководство пользователя страница 41

                                                                                                                             

Smart Machine Smart Decision

 

All camera pins can be configured for GPIOs by the AT command “

AT+CCGSWT”

. These GPIOs also 

support interruption operation if used as input pins. If these pins are configured for GPIOs, the sequence is 
listed in the following table. 

Table 20: GPIO configuration 

Pin name 

GPIO No. 

CAM_D2 

GPIO6 

CAM_D3 

GPIO7 

CAM_D4 

GPIO8 

CAM_D5 

GPIO9 

CAM_D6 

GPIO10 

CAM_D7 

GPIO11 

CAM_D8 

GPIO12 

CAM_D9 

GPIO13 

CAM_HSYNC 

GPIO14 

CAM_VSYNC 

GPIO15 

CAM_CLK 

GPIO16 

CAM_PCLK 

GPIO17 

CAM_RESET 

GPIO18 

CAM_STANDBY 

GPIO19 

 

Note: 

1.We have tested several kinds of digital sensors, such as OV2640, OV7670

，

OV7725 and a NTSC/PAL digital video 

decoder named AK8856.

 

Software must be adjusted before users adopt other kinds of sensors. 

2. Because of high bit rate on camera bus, pay attention to influence of junction capacitance of ESD component on clock 

and data lines. Typically, the capacitance should be less than 10pF. 

3. Pay attention to the polarity of power down pin in users’ sensor before designing. Default polarity of 

SIM5215A&SIM5216A is shown:    LOW: normal operation   HIGH: power-down. 

 

3.8

 

USB Interface 

SIM5215&SIM5216 module contains a USB interface. This interface is compliant with the USB2.0 
specification. The USB2.0 specification requires hosts such as the computer to support all three USB 
speeds, namely low-speed (1.5Mbps), full-speed (12Mbps) and high-speed (480Mbps). USB charging and 
USB-OTG is not supported. 
 

Table 21: Electronic characteristic 

Input voltage scope( V ) 

Pin name 

Pin No. 

Min 

Typ 

Max 

SIM5215&SIM5216_Hardware Design_V2.02 

 

2012-08-31 

41

Содержание SIM5215









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды