SimCom SIM5215 Скачать руководство пользователя страница 57

Страница: 57 / 72

Smart Machine Smart Decision

Reliability and Operating Characteristics

5.1

Electronic Characteristics

Absolute maximum rating for digital and analog pins of SIM5215&SIM5216 are listed in the following
table:

Table 39: Absolute maximum ratings

Parameter

Min

Max

Unit

Voltage at digital pins (1.8v mode)

-0.3

1.8+0.3 V

Voltage at digital pins (2.6v mode)

-0.3

2.6+0.3 V

Voltage at VBAT

-0.5

6.0

Voltage at VRTC

1.5

3.2

Voltage at USB_VBUS

-0.5

6.0

Table 40: Recommended operating ratings

Parameter

Min

Typ

Max

Unit

Voltage at digital pins (1.8v mode)

1.65

1.8

1.95

Voltage at digital pins (2.6v mode)

2.5

2.6

2.7

Voltage at VBAT

3.3

3.8

4.2

Voltage at VRTC

1.5

3.0

Voltage at USB_VBUS

4.75

5.25

The operating temperature and power specification is listed in the following table.

Table 41: Operating temperature

Parameter

Min

Typ

Max

Unit

Ambient temperature

-30

℃

Storage temperature

-40

+85

℃

Note: SIMCom recommends user to install a heat sink on the module shielding case if SIM5215&SIM5216 operates in

WCDMA band.

5.2

Operating Mode

The following table summarizes the various operating modes, each operating modes will be referred to in
the following chapters.

SIM5215&SIM5216_Hardware Design_V2.02

2012-08-31

Содержание SIM5215









































































Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды

SimCom SIM5215, Проектирование аппаратного обеспечения

Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды