manualshive.com logo in svg

SimCom SIM5215, Проектирование аппаратного обеспечения

Поделиться
Скачать
SimCom SIM5215 Скачать руководство пользователя страница 17

                                                                                                                             

Smart Machine Smart Decision

 

SD_DATA3 

I/O 

SDIO data 

USB 

USB_VBUS 

I 

USB power supply input 

USB_DP 

I/O 

Plus (+) line of the differential, 
bi-directional USB signal to/from the
peripheral device.

USB_DM 

I/O 

Minus (-) line of the differential, 
bi-directional USB signal to/from the
peripheral device.

They are compliant with 
the USB 2.0 specification.
If it is unused, keep open. 

Serial interface 

UART_RXD 

I 

Receive Data 

UART_TXD 

O 

Transmit Data 

UART_RTS 

O 

Request to send 

UART_CTS 

I 

Clear to Send 

UART_RI 

O 

Ring Indicator 

UART_DTR 

I/O 

DTE get ready 

UART_DCD 

O 

Carrier detects 

UART_RXD has been 
pulled down with a 12kR 
resistor to ground in the 
module. 
If it is unused, keep open. 

I2C interface 

I2C_SDA 

I/O 

I2C data 

I2C_SCL 

O 

I2C clock output 

Pulled up with a 2.2kR 
resistor to 2.6V internally.
If it is unused, keep open. 

Camera interface 

CAM_CLK 

O 

Camera clock 

CAM_PCLK 

I 

Camera pixel clock

 

CAM_VSYNC 

I 

Horizontal synchronization

 

CAM_HSYNC 

I 

Vertical synchronization

 

CAM_STANDBY 

O 

Power down control

 

CAM_RESET 

O 

Reset control 

CAM_D2 

I 

Data bit 0 (YUV or RGB)

 

CAM_D3 

I 

Data bit 1 (YUV or RGB)

 

CAM_D4 

I 

Data bit 2 (YUV or RGB)

 

CAM_D5 

I 

Data bit 3 (YUV or RGB)

 

CAM_D6 

I 

Data bit 4 (YUV or RGB) 

CAM_D7 

I 

Data bit 5 (YUV or RGB) 

CAM_D8 

I 

Data bit 6 (YUV or RGB) 

CAM_D9 

I 

Data bit 7 (YUV or RGB) 

All camera pins can be 
configured as GPIOs.   
If it is unused, keep open.

 

PCM interface 

PCM_DIN/GPIO0 

I 

General Input PIN with module 
wake/interrupt. It also can be 
multiplexed as the PCM_DIN pin. 

PCM_SYNC/GPIO2 

I 

General Input PIN. It also can be 
multiplexed as the PCM_SYNC pin. 

PCM_CLK/GPIO3 

O 

General Output PIN. It also can be 
multiplexed as the PCM_CLK pin. 

If it is unused, keep open. 

SIM5215&SIM5216_Hardware Design_V2.02 

 

2012-08-31 

17

Содержание SIM5215









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды