manualshive.com logo in svg

SimCom SIM5215, Проектирование аппаратного обеспечения

Поделиться
Скачать
SimCom SIM5215 Скачать руководство пользователя страница 30

                                                                                                                             

Smart Machine Smart Decision

 

 

Figure 20: RI behaviour in NULL Modem 

 

If Full Modem is used to establish communication between devices, the pin “RI” is another operation 
status. Initially it keeps high, when a voice call or CSD call comes, the pin “RI” will change to low for 
about 5900ms, then it will return to high level for 100ms. It will repeat this procedure until this call is 
answered or hung up.   
 

 

Figure 21: RI behaviour in FULL Modem 

 

To comply with RS-232 protocol, the RS-232 level shifter chip should be used to connect 
SIM5215&SIM5216 to the RS-232-C interface. In this connection, the TTL level and RS-232 level are 
converted mutually. SIMCom recommends that user uses the SP3238ECA chip with a full modem. For 
more information please refers to the RS-232 chip datasheet. 

 

Note: SIM5215&SIM5216 supports the communication rate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 

115200, 230400, 460800, 921600, 3200000, 3686400, 4000000bps. Default rate is 115200bps. 

 

3.4

 

Audio Interfaces 

SIM5215&SIM5216 provides three analog signal outputs and two analog input. MIC1P/N and HP_MICP 
is used as microphone, HPL/R, EAR1P/N and SPK_P/N are used as audio output. Regarding audio 
parameters configuration, please refer to the ATC manual. 

SIM5215&SIM5216_Hardware Design_V2.02 

 

2012-08-31 

30

Содержание SIM5215









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды