manualshive.com logo in svg

SimCom SIM5215, Проектирование аппаратного обеспечения

Поделиться
Скачать
SimCom SIM5215 Скачать руководство пользователя страница 46

                                                                                                                             

Smart Machine Smart Decision

 

 

Figure 33: Flight mode switch 

 

Table 27: Control status 

GPIO4 Status 

Module operation 

Low Level 

Flight Mode: RF is closed. 

High Level 

Normal Mode: RF is working. 

 

Note

：

1. For SIM5215&SIM5216, GPIO0, GPIO2, GPIO3 and GPIO5 have multiplex function, user can use them as 

PCM interface to connect extend codec. Refer to section 3.10 and document [1] for details. 

2. When the module is powered off, make sure all digital interfaces (PCM UART, etc) connected with peripheral devices 

have no voltage higher than 0.3V. If users’ design cannot meet above conditions, high level voltages maybe occur in 

GPIO pins because current leakage from above digital interfaces may occur. 

 

3.11

 

PCM Interface 

SIM5215&SIM5216 provides hardware PCM interface for external codec. The PCM interface enables 
communication with an external codec to support hands-free applications. SIM5215&SIM5216 PCM 
interface can be used in two modes: the default mode is auxiliary PCM (8 KHz long sync mode at 128 
KHz PCM CLK); the other mode is primary PCM (8 KHz short sync mode at 2048 KHz PCM CLK).    In 
short-sync (primary PCM) mode, SIM5215&SIM5216 can be a master or a slave. In long-sync (auxiliary 
PCM) mode, SIM5215&SIM5216 is always a master. SIM5215&SIM5216 also supports 3 kinds of 
coding formats: 8 bits (

υ

-law or A-law) and 16 bits (linear). 

 

Note: PCM interface is multiplexed from GPIO (default setting). The AT command “AT+CPCM” is used to switch 

between PCM and GPIO functions. Please refer to document [22] and document [1] for details. 

 

SIM5215&SIM5216_Hardware Design_V2.02 

 

2012-08-31 

46

Содержание SIM5215









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды