SimCom SIM5215 Скачать руководство пользователя страница 27

Страница: 27 / 72

Smart Machine Smart Decision

3.2.2

Power off Sequence

The following methods can be used to power down SIM5215&SIM5216. These procedures will make
module disconnect from the network and allow the software to enter a safe state, and then save data before
completely powering the module off.

●

Method 1: Power off SIM5215&SIM5216 by pulling the POWER_ON pin down

●

Method 2: Power off SIM5215&SIM5216 by AT command

User can power off the SIM5215&SIM5216 by pulling POWER_ON down for a specific time. The power
off scenario is illustrated in the following figure.

Figure 17: Power off timing sequence

Table 7: Power off timing

Time value

Parameter

Description

Min.

Typ.

Max.

Unit

Toff

The time pulling POWER_ON down to power off

0.5

TpD-

The time to indicate disconnecting from the network

Tpw-

The time to indicate the module power off completely

7.5

Tuart_off

The time to disable UART

Tusb_off

The time to disable USB

7.5

SIM5215&SIM5216_Hardware Design_V2.02

2012-08-31

Содержание SIM5215









































































Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды

SimCom SIM5215, Проектирование аппаратного обеспечения

Результаты поиска

Содержание SIM5215

Отзывы:

Бренды по названию

Популярные бренды