Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual
risk factors. Use with caution. If you are at all unsure of the correct and
safe manner in which to use this tool, do not attempt to use it.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions.
Failure to
follow the warnings and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work Area Safety
a)
Keep work area clean and well lit.
Cluttered or dark areas invite
accidents
b)
Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust.
Power
tools create sparks which may ignite the dust or fumes
c)
Keep children and bystanders away while operating a power
tool.
Distractions can cause you to lose control
Electrical Safety
a)
Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock
b)
Avoid body contact with earthed or grounded surfaces, such
as pipes, radiators, ranges and refrigerators.
There is an
increased risk of electric shock if your body is earthed or grounded
c)
Do not expose power tools to rain or wet conditions.
Water
entering a power tool will increase the risk of electric shock
d)
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
oil, sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock
e)
When operating a power tool outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock
f)
If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply.
Use of an RCD
reduces the risk of electric shock
NOTE:
The term “residual current device (RCD)” may be replaced
by the term “ground fault circuit interrupter (GFCI)” or “earth
leakage circuit breaker (ELCB)”.
Personal Safety
a)
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury
b)
Use personal protective equipment. Always wear eye
protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries
c)
Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents
6
GB
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protectio
Wear head protection
Wear hand protection
Read Instruction Manual
Class I construction (Protective earth)
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice
Specification
Power ...................................................250W
Input .....................................................230~ 50Hz
No load speed ......................................1400min
-1
Line speed of blade ..............................15m/s
Table size .............................................300 x 300mm
Table tilt ...............................................0° - 45°
Max width of cut ..................................200mm
Max depth of cut ..................................80mm
Max cutting height (90°) .......................80mm
Max cutting height (45°) .......................45mm
Sound pressure (Lp) .............................77.4 dB(A)
Sound power (Lw) ................................90.4 dB(A)
Uncertainty ...........................................3 dB
Protection class ....................................Class I
Table height .........................................90mm
Blade width (max) ................................8mm
Cord length ..........................................2m
Weight ..................................................15.5kg
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
613578_Z1MANPRO1.indd 4
28/11/2012 11:38
Содержание 613578
Страница 4: ...4...
