Silverline 454954, Руководство пользователя

Страница: 9 / 44

www.silverlinetools.com
9
400W Mini Saw 454954
WARNING: ONLY use a compatible saw blade that is the same dimensions as the saw
blade described in the ‘Specifications’.
1. Pull off the Spindle Access Cap (9) to gain access to the Blade Securing Bolt (10)
2. Secure the Spindle Lock Nut (13) using the Spindle Lock Key (2)
3. Remove the Blade Securing Bolt by turning the Hex Key (1) clockwise
4. Insert the desired Blade through the opening in the bottom of the Blade Guard (12)
5. Position the Blade concentrically on the spindle (Image A) and fasten into place using
the Blade Securing Bolt
Dust extraction
WARNING: Always connect the tool to a suitable vacuum cleaner or workshop dust
extraction system if the sanding dust contains harmful substances, such as particles from
old paint, varnish, surface coatings etc. Always dispose of harmful dust according to laws
and regulations.
WARNING: Take special care to guard against harmful and toxic dusts when working with
lead-based painted surfaces, woods and metals, particularly if you are unsure about the
exact substances involved. All persons entering the work area must wear a mask specially
designed for protection against the toxic dust and fumes involved. Children and pregnant
women MUST NOT enter the work area. DO NOT eat, drink or smoke in the work area.
• Slide the Hose End (16) on to the Dust Extraction Port (6) (Image B)
• Use the Hose Clamp (17) to secure the Hose End to the Dust Extraction Port
• Insert the Dust Extraction Adaptor (18) into the dust extractor inlet
Cutting depth adjustment
1. To adjust the cutting depth of the tool, first loosen the Cutting Depth Adjustment
Knob (3)
2. Align the end of the Depth Adjustment Slider (5) with the desired cutting depth
designation on the Cutting Depth Graduation Scale (7) (Image C)
3. Tighten the Cutting Depth Adjustment Knob
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection,
as well as suitable gloves, when working with this tool.
Switching on and off
WARNING:
• Switch the tool on by depressing the On/Off Slider Switch (4) and slide downwards
towards the Blade Guard (12)
• Switch the tool off by releasing the On/Off Slider Switch
Performing a cut
WARNING: Always ensure the workpiece is adequately secured using clamps and/or a vice
at all times. Do not attempt to use this tool without sufficiently securing the workpiece first.
• The cutting plane is indicated by the arrow located at the front and rear of the Blade
Guard (12)
• Switch the tool on, wait for the Blade to reach normal operating speed and depress
the Cut Release Lever (14) to commence cutting
• Press down on the Handle (15) and allow the Blade (11) to engage the workpiece
• For dense materials work slowly and cut in multiple depth stages if necessary to
reduce the load on the motor, i.e. split a 12mm depth cut into two cuts of 6mm, first to
the depth of 6mm and the second to the depth of 12mm
• Ensure the correct blade is fitted for the material being cut
• Always push the saw forwards. NEVER pull the saw backwards towards you
• When starting the cut, ensure the rear of the Blade Guard is protruding off the edge
of the workpiece
• Ensure the Blade Guard is always kept flat against the workpiece when cutting
• When finished cutting, release the Cut Release Lever (14) and raise the Blade out
of the workpiece. Maintain Blade velocity for a short period to remove all dust from
the cutting area
Accessories
• A range of accessories and consumables, including replacement saw blades,
is available from your SILVERLINE stockist. Spare parts can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any
inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs
should be carried out by an authorised SILVERLINE service centre. This advice also
applies to extension cords used with this tool
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the device’s service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild
detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes
(where applicable)
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible
sparking
• If you suspect that the brushes may be worn, have them replaced at an authorised
SILVERLINE service centre
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer
functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment
(WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way to
dispose of power tools
454956_Z1MANPRO1.indd 9 02/12/2015 09:45