SILLA PRISM SOLAR RFID Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

Location of assembly

The installation of Prism must be carried out by qualiﬁed personnel in accordance with
the applicable regulations. Local electrical installation regulations, ﬁre and accident
prevention measures and emergency routes from the point of installation must be taken
into account.
Please contact an electrician or arrange installation at your utility with your local
distributor.
Find a location for the Prism that allows the vehicle to be within easy reach of the
integrated charging cable.
We recommend an installation height of 130 - 170 cm between the ﬂoor and the lower
edge of the outer structure.

Su cient air circulation must be ensured in the installation position
so that the Prism cools down when it is recharging.

The mounting surface must have a ﬂat base that provides su cient stability for
mounting the Prism, taking into account the possible mechanical stresses resulting
from the use of the charging cable.
It must be ensured that the maximum permissible operating temperature cannot be
exceeded under the inﬂuence of external inﬂuences such as direct sunlight or similar.
Prism meets the requirements for outdoor installation. In order to minimise dirt and
weather wear, it is recommended that the Prism be mounted outdoors in a covered area.

Do not install the Prism in the vicinity of ﬂammable, explosive or
combustible materials, chemicals or solvents, gas pipes or steam
vents, radiators or batteries, as well as in areas subject to ﬂooding,
high humidity or running water. Do not install Prism in direct sunlight.

Prism SOLAR rel. 2.2.2

- 5

«
...
5
6
7
8
9
...
»

Содержание PRISM SOLAR RFID





















































Отзывы:

Нет отзывов

Похожие инструкции для PRISM SOLAR RFID

Markoprint iJET

Бренд: Weber Страницы: 127

Бренд: Daewoo Страницы: 21

Бренд: Medion Страницы: 220

iAqualink IQ904-P

Бренд: Zodiac Страницы: 2

Бренд: Ruida Technology Страницы: 35

Бренд: Daewoo Страницы: 21

Бренд: DAEWOO ELECTRONICS Страницы: 7

Бренд: Ricatech Страницы: 64

Бренд: WITTUR Страницы: 47

Бренд: GATE ARMS+ Страницы: 12

Бренд: PVI Страницы: 12

Бренд: Hitachi Страницы: 169

Бренд: morse Страницы: 9

Factory Line 20

Бренд: Panasonic Страницы: 12

Бренд: ZANDER Страницы: 16

Бренд: Norco Страницы: 2

Бренд: JVC Страницы: 2

Бренд: JVC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды