background image

Flow rate exceeds display capability

• Open Collector pulse rate exceeds

maximum of 300 pulses per minute.

• Pulse width set too wide.

K-factors cannot be set to 0.

• Hysteresis value too large
• Defective transmitter

Troubleshooting

Display Condition

Suggested Solutions

Suggested Solutions

• Increase Flow units timebase
•  Move flow decimal one place to the right

•  Increase Output Volume setting
•  Decrease Output pulse width
•  Reduce system flow rate

Enter K-factor between 0.0001 to 99999

•  Change the hysteresis value
• Replace transmitter

“-  -  -  -  -”

“Pulse Overrun Output1”
“Pulse Overrun Output2”

“Value must be more than 0”

Open Collector output is always
activated

‡ SIGNET

Signet Scientific Company, 3401 Aerojet Avenue, El Monte, CA  91731-2882  U.S.A.  •  Tel. (626) 571-2770  •  Fax (626) 573-2057
For Worldwide Sales and Service, visit our website:  www.gfsignet.com  •  Or call (in the U.S.):  (800) 854-4090

GEORGE FISCHER ‡ Piping Systems

3-8550.090-3/(F-4/03) English

 © Signet Scientific Company 2002

Printed in U.S.A. on recycled paper

Ordering Information

Mfr. Part No.

Code

Description

3-8550-1

159 000 047

Flow transmitter, Field mount

3-8550-1P

159 000 048

Flow transmitter, Panel mount

3-8550-2

159 000 049

Flow transmitter, Field mount with relays

3-8550-2P

159 000 050

Flow transmitter, Panel mount with relays

3-8550-3

159 000 051

Flow transmitter, Field mount with dual input/output

3-8550-3P

159 000 052

Flow transmitter, Panel mount with dual input/output

Accessories

Mfr. Part No.

Code

Description

3-8050

159 000 184

Universal mounting kit

3-8051

159 000 187

Flow Integral Mnt NPT

3-8050.395

159 000 186

Splashproof rear cover

3-8050.396

159 000 617

RC Filter kit (for relay use)

3-0000.596

159 000 641

Heavy duty wall mount bracket

3-5000.598

198 840 225

Surface Mount Bracket

3-5000.599

198 840 224

5 x 5 inch adapter plate for +GF+ SIGNET retrofit

3-9000.392

159 000 368

Liquid tight connector kit for rear cover (includes 3 connectors)

3-9000.392-1

159 000 839

Liquid tight connector kit, NPT (1 piece)

3-9000.392-2

159 000 841

Liquid tight connector kit, PG13.5 (1 piece)

7300-7524

159 000 687

24 VDC Power Supply 7.5 W, 300mA

7300-1524

159 000 688

24 VDC Power Supply 15 W, 600mA

7300-3024

159 000 689

24 VDC Power Supply 30 W, 1.3 A

7300-5024

159 000 690

24 VDC Power Supply 50 W, 2.1 A

7300-1024

159 000 691

24 VDC Power Supply 100 W, 4.2 A

Содержание 8550-3









Отзывы: