SiFive FE310-G003 Скачать руководство пользователя страница 105

Страница: 105 / 121

pwmcmp1ip

PWM1 Interrupt Pending

pwmcmp2ip

PWM2 Interrupt Pending

pwmcmp3ip

PWM3 Interrupt Pending

The

pwmcfg

eral, as shown in Table 90.

The

pwmen*

bits control the conditions under which the PWM counter

pwmcount

is incremented.

The counter increments by one each cycle only if any of the enabled conditions are true.

If the

pwmenalways

bit is set, the PWM counter increments continuously. When

pwmenoneshot

is set, the counter can increment but

pwmenoneshot

is reset to zero once the counter resets,

disabling further counting (unless

pwmenalways

is set). The

pwmenoneshot

bit provides a way

for software to generate a single PWM cycle then stop. Software can set the

pwmenoneshot

again at any time to replay the one-shot waveform. The

pwmen*

bits are reset at wakeup reset,

which disables the PWM counter and saves power.

The 4-bit

pwmscale

field scales the PWM counter value before feeding it to the PWM compara-

tors. The value in

pwmscale

is the bit position within the

pwmcount

cmpwidth

-bit

pwms

field. A value of 0 in

pwmscale

indicates no scaling, and

pwms

would then be

equal to the low

cmpwidth

bits of

pwmcount

. The maximum value of 15 in

pwmscale

corre-

sponds to dividing the clock rate by 2

, so for an input bus clock of 16 MHz, the LSB of

pwms

will increment at 488.3 Hz.

The

pwmzerocmp

bit, if set, causes the PWM counter

pwmcount

to be automatically reset to zero

one cycle after the

pwms

counter value matches the compare value in

pwmcmp0

. This is normally

used to set the period of the PWM cycle. This feature can also be used to implement periodic
counter interrupts, where the period is independent of interrupt service time.

19.6

Scaled PWM Count Register (

pwms

)

The Scaled PWM Count Register

pwms

reports the

cmpwidth

-bit portion of

pwmcount

which

starts at

pwmscale

, and is what is used for comparison against the

pwmcmp

registers.

Scaled PWM Count Register (

pwms

)

Register Offset

0x10

Bits

Field Name

Attr.

Rst.

Description

[15:0]

pwms

Scaled PWM count register.

cmpwidth

bits wide.

Table 90:

PWM Configuration Register

Table 91:

Scaled PWM Count Register

Chapter 19 Pulse Width Modulator (PWM)

FE310-G003 Manual

© SiFive, Inc.

Page 103

Содержание FE310-G003


























































































































Результаты поиска

Содержание FE310-G003

Отзывы:

Похожие инструкции для FE310-G003

Бренды по названию

Популярные бренды

SiFive FE310-G003, Руководство пользователя

Результаты поиска

Содержание FE310-G003

Отзывы:

Похожие инструкции для FE310-G003

Бренды по названию

Популярные бренды