Sierra Wireless AirPrime WP75 Series, Справочник по командам AT

Страница: 291 / 300

Index — AT Commands
Rev. 6 Oct.18 Proprietary and Confidential - Contents subject to change 291
ture , 50
EXTGPSLNAEN, Enable/disable EXT_GPS_LNA_EN ,
50
EXTUIMSWITCHEN, Enable/disable fast SIM switch via
external switch , 50
FASTBOOTEN, Enable/disable Fastboot port , 50
FASTENUMEN, Enable/disable fast enumeration , 50
FLOWNOTIDISABLE, Enable/disable QMI notification
events , 51
GPIOSARENABLE, Control SAR backoff by GPIOs or by
AT commands , 51
GPSLPM, enable GPS in low power mode , 51
GPSREFLOC, enable GPS location reporting , 51
GPSSEL, select antenna for GPS , 51
HARDCODEDIPEN, hard-coded IP enable/disable , 51
HSICENABLE, enable/disable HSIC interface , 52
ICMPINTSRVDIS, enable/disable internal ICMP ser-
vice , 52
IMCONFIG, image switching configuration , 52
IPCHANNELRATEEN, Enable/disable IP channel rate
calculation , 52
JAMENABLE, JAM detection enable/disable , 52
LTECOEXUARTENABLE, Wi-Fi/LTE Coex control
enable/disable , 52
LTEREJDELAY, Set delay before LTE attach requests
are sent , 52
PCSCDISABLE, set PCSC functionality , 53
RMNETREDIALEN, RmNet redial enable/disable , 53
SIMHOTSWAPDIS, Configure SIM hotswap feature , 53
SIMLPM, set default low power mode SIM power state ,
53
SINGLEAPNSWITCH, device behaviour when APN de-
tails change, customize , 53
SKUID, set device SKU ID , 53
SNTPEN, enable SNTP system time support , 53
STKUIEN, enable SIM toolkit UI , 54
UIMAUTOSWITCH, enable/disable automatic SIM
switching , 54
UIMDETPULL, configure UIM1/UIM2 detect line pull set-
tings , 54
WAKEHOSTEN, enable/disable host wake-up via SMS/
incoming data packet , 54
WAKEHOSTEN, Host wake-up method, enable/disable ,
54
!CUSTOM, customization settings, set/query , 187
+CV120, v.120 rate adaption protocol , 283
+CVHU, voice hangup control , 283
+CVIB, vibrator mode , 283
D
&D, set DTR function mode , 275
D, dial , 276
D, ITU T V.25ter dial command , 283
D’99’’’<n>#, set up packet data call based on profile ID #<n> ,
283
D’99#, set up packet call based on profile ID #1 , 283
D><MEM><N>, originate call to phone number in memory ,
276
D><N>, originate call to phone number in current memory ,
276
D><STR>, originate call to phone number corresponding to a/
n field
, 276
!DACGPSCTON, return CGPS C/N and frequency , 164
!DACGPSMASKON, set CGPS log mask , 164
!DACGPSSTANDALONE, enter/exit Stand Alone (SA) RF
mode
, 165
!DACGPSTESTMODE, start/stop CGPS diagnostic task , 165
!DAFTMACT, put modem into FTM mode , 13, 161, 166
!DAFTMDEACT, put modem into online mode , 166
!DAGGAVGRSSI, return averaged RSSI , 167
!DAGSRXBURST, set GSM receiver to burst mode , 167
!DAGSTXFRAME, set GSM Tx frame structure , 168
!DALSNSVAL, configure LTE Net Sig value , 169
!DALSPARANGE, set PA range (LTE mode) , 169
!DALSRXBW, set Rx bandwidth (LTE mode) , 170
!DALSTXBW, set Tx bandwidth (LTE mode) , 170
!DALSTXMOD, set LTE Tx modulation type , 171
!DALSTXPWR, set Tx power level , 172
!DALSWAVEFORM, set Tx waveform (LTE mode) , 173
!DASBAND, set frequency band , 13, 161, 174
!DASCHAN, set modem channel (frequency) , 175
!DASLNAGAIN, set LNA gain state , 176
!DASPDM, set PDM value , 177
!DASTXOFF, turn Tx PA off , 177
!DASTXON, turn Tx PA on , 178
!DATALOOPBACK, enable/disable and configure loopback
mode
, 55
!DAWGAVGAGC, return averaged Rx AGC (WCDMA) , 178
!DAWSPARANGE, set PA range state machine , 179
!DAWSSCHAIN, enable secondary receive chain , 179
!DAWSTXCW, select transmitter waveform , 180
!DAWSTXPWR, set Tx power level , 180
DL, redial last phone number used , 276
+DR, V42bis compression report , 275
+DS, V42bis data compress , 275
E
E, set command echo mode , 276
!ENTERCND, enable protected command access , 13, 26, 27
!EONS, EONS indicator (unsolicited notification) , 55
!ERR, display diagnostic information , 159
!EVRC_B, Vocoder in use (unsolicited notifications) , 56
!EVRC, Vocoder in use (unsolicited notifications) , 55
!EVRC_NW, Vocoder in use (unsolicited notifications) , 56
!EVRC_WB, Vocoder in use (unsolicited notifications) , 56
F
&F, set current parameters to defaults , 275
G
+GCAP, Request complete TA capabilities list , 275
!GCCLR, clear crash dump data , 159
!GCDUMP, display crash dump data , 159